VEHICLE STABILITY CONTROL SYSTEM > PRECAUTION |
| 1.PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL |
| System | See Procedure |
| Parking Assist Monitor System |
Click here
|
| 2.IGNITION SWITCH EXPRESSIONS |
| Expression | Ignition Switch (Position) | Engine Switch (Condition) |
| Ignition Switch off | LOCK | Off |
| Ignition Switch ACC | ACC | On (ACC) |
| Ignition Switch ON | ON | On (IG) |
| Engine Start | START | Start |
| 3.TROUBLESHOOTING PRECAUTIONS |
When there is a malfunction with terminal contact points or part installation problems, removal and installation of the suspected parts may return the system to normal either completely or temporarily.
In order to determine the malfunctioning area, be sure to check the conditions at the time the malfunction occurred, such as DTC output and the Freeze Frame Data, and record it before disconnecting any connector or removing and installing parts.
Since the system may be influenced by malfunctions in systems other than the VSC system, be sure to check for DTCs in other systems.
| 4.HANDLING PRECAUTIONS |
Do not remove or install VSC parts such as the steering angle sensor, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) except when required, as they need to be adjusted correctly after removal and installation.
Be sure to perform preparation before work and confirmation after work is completed by following the directions in the repair manual when working on the VSC system.
Be sure to remove and install the ECU, brake actuator assembly, sensors, etc. with the ignition switch off unless it is otherwise specified in the inspection procedure.
If the ECU, brake actuator assembly or a sensor has been removed and installed, it is necessary to check the system for problems after the parts have been reassembled. Check for DTCs using the Techstream, also check that system functions and signals received by the ECU are normal using Test Mode.
| 5.DTC PRECAUTION |
Warnings for some DTCs cannot be cleared only by repairing the malfunctioning parts. If the warning is displayed after repair work, the DTC should be cleared after turning the ignition switch off.
| 6.CHASSIS DYNAMOMETER PRECAUTION |
Activating Inspection Mode (When Using the Techstream)
Ensure that the ignition switch is off and the engine is stopped.
Make sure that the shift lever is in P.
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Inspection Mode.
Check that the slip indicator light will come on.
Activating Inspection Mode (When not Using the Techstream)
Ensure that the ignition switch is off and the engine is stopped (Step "A").
Make sure that the shift lever is in P (Step "B").
Start the engine (Step "C").
Apply the parking brake by depressing the parking brake pedal (Step "D").
Depress and release the brake pedal twice (Step "E").
While holding the brake pedal down, release and apply the parking brake twice (Step "F").
With the parking brake applied, depress and release the brake pedal twice (Step "G").
Check if the slip indicator light will come on (Step "H").
| 7.CAN COMMUNICATION SYSTEM PRECAUTIONS |
The CAN communication system is used for communication between the skid control ECU (brake actuator assembly), the steering angle sensor, the yaw rate and acceleration sensor (for separate type) or the yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) and other ECUs. If any CAN communication DTCs are detected, DTCs corresponding to the malfunction will be output.
If any CAN communication DTCs are output, repair the malfunction and troubleshoot the VSC system while communication is normal.
In order to enable CAN communication, a specific type of wiring is used for the CAN communication lines. The wiring used for each communication line is a twisted pair of wires that have an equal length. A bypass wire should not be used because the data being transmitted will be corrupted.