Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.
  3. If DTC P0352 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.
  4. If DTC P0353 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.
  5. If DTC P0354 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.
  6. If DTC P0355 is output, check the No. 5 ignition coil assembly (No. 5 cylinder) circuit.
  7. If DTC P0356 is output, check the No. 6 ignition coil assembly (No. 6 cylinder) circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A256625E01


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil assembly and ECM
  3. No. 1 to No. 6 ignition coil assemblies
  4. ECM

  1. A210049E07
    Reference: Inspection using an oscilloscope
  2. While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connectors.
    ECM Terminal Name
    Between IGT (1 to 6) and E1
    Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION


A212405E11

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) range check/functional check
P0352: Igniter (cylinder 2) range check/functional check
P0353: Igniter (cylinder 3) range check/functional check
P0354: Igniter (cylinder 4) range check/functional check
P0355: Igniter (cylinder 5) range check/functional check
P0356: Igniter (cylinder 6) range check/functional check
Required Sensors/Components (Main)
Igniter (Cylinder 1 to 6)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
None
All of the following conditions are met
-
Spark cut
Not operating
Either of the following conditions is met
A or B
A. Starter
Off
B. Engine speed
1500 rpm or less
Either of the following conditions is met
C or D
C. Both of the following conditions are met
-
Engine speed
500 rpm or less
Battery voltage
6 V or higher
D. All of the following conditions are met
-
Engine speed
Higher than 500 rpm
Battery voltage
10 V or higher
Number of sparks after CPU is reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


All of the following conditions are met
A, B, C and D
A. Ignition signal fail counter
More than 2 times
B. Time after condition A is met
0.256 seconds or more
C. Ignition signal fail counter after condition B is met
More than 2 times
D. Engine switch
On (IG)

COMPONENT OPERATING RANGE


Confirmed ignition signal input when ignition signal is on to off
2 times

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine / Trouble Codes [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  13. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A255658E01


A266382E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-4 (GND) - Body ground
    Always
    Below 1 Ω
    E41-4 (GND) - Body ground
    Always
    Below 1 Ω
    E38-4 (GND) - Body ground
    Always
    Below 1 Ω
    E42-4 (GND) - Body ground
    Always
    Below 1 Ω
    E39-4 (GND) - Body ground
    Always
    Below 1 Ω
    E44-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)


    A194110E70
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E37-1 (+B) - E37-4 (GND)
    Engine switch on (IG)
    11 to 14 V
    E41-1 (+B) - E41-4 (GND)
    Engine switch on (IG)
    11 to 14 V
    E38-1 (+B) - E38-4 (GND)
    Engine switch on (IG)
    11 to 14 V
    E42-1 (+B) - E42-4 (GND)
    Engine switch on (IG)
    11 to 14 V
    E39-1 (+B) - E39-4 (GND)
    Engine switch on (IG)
    11 to 14 V
    E44-1 (+B) - E44-4 (GND)
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-3 (IGT1) - E26-107 (IGT1)
    Always
    Below 1 Ω
    E41-3 (IGT2) - E26-140 (IGT2)
    Always
    Below 1 Ω
    E38-3 (IGT3) - E26-106 (IGT3)
    Always
    Below 1 Ω
    E42-3 (IGT4) - E26-139 (IGT4)
    Always
    Below 1 Ω
    E39-3 (IGT5) - E26-105 (IGT5)
    Always
    Below 1 Ω
    E44-3 (IGT6) - E26-138 (IGT6)
    Always
    Below 1 Ω
    E37-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E41-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E38-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E42-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E39-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E44-2 (IGF) - E26-103 (IGF1)
    Always
    Below 1 Ω
    E37-3 (IGT1) or E26-107 (IGT1) - Body ground
    Always
    10 kΩ or higher
    E41-3 (IGT2) or E26-140 (IGT2) - Body ground
    Always
    10 kΩ or higher
    E38-3 (IGT3) or E26-106 (IGT3) - Body ground
    Always
    10 kΩ or higher
    E42-3 (IGT4) or E26-139 (IGT4) - Body ground
    Always
    10 kΩ or higher
    E39-3 (IGT5) or E26-105 (IGT5) - Body ground
    Always
    10 kΩ or higher
    E44-3 (IGT6) or E26-138 (IGT6) - Body ground
    Always
    10 kΩ or higher
    E37-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher
    E41-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher
    E38-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher
    E42-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher
    E39-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher
    E44-2 (IGF) or E26-103 (IGF1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B

    HINT:
    Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the ignition coil assembly connectors.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E37-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E41-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E38-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E42-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E39-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E44-1 (+B) - 1A-1
    Always
    Below 1 Ω
    E37-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher
    E41-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher
    E38-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher
    E42-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher
    E39-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher
    E44-1 (+B) or 1A-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)