DTC C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1330 Open in Front Speed Sensor RH |
DTC C1331 Open in Front Speed Sensor LH |
DTC C1464 Front Speed Sensor RH |
DTC C1465 Front Speed Sensor LH |

| DTC No. | DTC Detection Condition | Trouble Area |
| C1464 C1465 | Any of the following is detected:
|
|
| C1330 C1331 | An open or short in the speed sensor signal circuit. |
|
| C1271 C1272 | Detected only during Test Mode. |
|

| 1.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Select the Data List using the Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the Techstream.
|
| ||||
| OK | |
| 2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1330, C1331, C1464 and C1465 are not output. | A |
| DTCs C1330, C1331, C1464 and/or C1465 are output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK FRONT SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 5.CHECK FRONT SPEED SENSOR AND SENSOR ROTOR |
Remove the front speed sensor and the component with the sensor rotor (Click here for speed sensor, Click here 2GR-FE for sensor rotor, and/or Click here 2AR-FE for sensor rotor).
Check the speed sensor tip and speed sensor rotor.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Install the front speed sensor and the component with the sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-16 (FR+) - A53-1 (FR+) | Always | Below 1 Ω |
| A49-16 (FR+) - Body ground | Always | 10 kΩ or higher |
| A49-4 (FR-) - A53-2 (FR-) | Always | Below 1 Ω |
| A49-4 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A49-19 (FL+) - A16-1 (FL+) | Always | Below 1 Ω |
| A49-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A49-8 (FL-) - A16-2 (FL-) | Always | Below 1 Ω |
| A49-8 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.RECONFIRM DTC |
Reconnect the skid control ECU connector and the front speed sensor connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1330, C1331, C1464 and/or C1465 are output. | A |
| DTCs C1330, C1331, C1464 and C1465 are not output. | B |
|
| ||||
| A | |
| 8.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 9.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1330, C1331, C1464 and/or C1465 are output. | A |
| DTCs C1330, C1331, C1464 and C1465 are not output. | B |
|
| ||||
| A | |
| 10.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY |
Turn the ignition switch off.
Replace the front speed sensor rotor (front drive outboard joint shaft assembly) (Click here for 2GR-FE, or Click here for 2AR-FE).
| NEXT | |
| 11.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1330, C1331, C1464 and C1465 are not output. | A |
| DTCs C1330, C1331, C1464 and/or C1465 are output. | B |
|
| ||||
| A | ||
| ||