Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1425    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.
The skid control ECU has a detection circuit that it uses to detect an open in the stop light input line.
If the skid control ECU detects an open in this circuit, it will store this DTC.

DTC No.
DTC Detection Condition
Trouble Area
C1425
An open in the stop light switch input line continues for 3 seconds or more.
  1. STOP fuse
  2. Stop light switch assembly
  3. Stop light switch circuit
  4. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

Refer to DTC C1249 .

INSPECTION PROCEDURE

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
Go to step 4
OK


2.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays on or off according to brake pedal operation.



NG
Go to step 8
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1425 is not output.
    A
    DTC C1425 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C173882E08
  1. Check that the STOP (7.5 A) fuse is normal.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C239673E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C238832E06
  1. Reconnect the stop light switch assembly connector.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    A49-30 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


7.RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1425 is not output.
    A
    DTC C1425 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)  

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C238832E06
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    A49-30 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)