DTC C2141/41 Transmitter ID1 Error |
DTC C2142/42 Transmitter ID2 Error |
DTC C2143/43 Transmitter ID3 Error |
DTC C2144/44 Transmitter ID4 Error |
| DTC No. | DTC Detection Condition | Trouble Area |
| C2141/41 C2142/42 C2143/43 C2144/44 | If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area. |
|
| 1.IDENTIFY TRANSMITTER CORRESPONDING TO DTC |
Set the tire pressure to the specified value .
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Display the "ID Tire Inflation Pressure" data for each wheel using the Techstream.
Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If "ID Tire Inflation Pressure" displayed on the Techstream (ID1 to ID4) does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" data was the cause of the output DTC.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
Check the Data List.
| Result | Detection Condition |
| One of "ID Tire Inflation Pressure" data (ID1 to ID4) changed. | Normal |
| "ID Tire Inflation Pressure" data did not change. | Transmitter corresponding to DTC |
When the "ID Tire inflation Pressure" data (ID1 to ID4) has changed, repeat this procedure to identify the tire pressure warning valve and transmitter that corresponds to the DTC.
When all of the "ID Tire Inflation Pressure" data (ID1 to ID4) has changed, identify the malfunctioning tire pressure warning valve and transmitter using the recorded ID numbers and output DTCs.
| NEXT | |
| 2.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER |
Replace the identified tire pressure warning valve and transmitter with a new one (Click here).
| NEXT | |
| 3.REGISTRATION OF TRANSMITTER ID |
Register the transmitter ID for all wheels (Click here).
| NEXT | |
| 4.PERFORM INITIALIZATION |
Perform initialization (Click here).
| NEXT | |
| 5.CONFIRM TIRE INFLATION PRESSURE (DATA LIST) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| ID4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 50 kPa (0.5 kgf/cm2, 7 psi), Relative pressure / -50 kPa (-0.5 kgf/cm2, -7 psi) max.: Absolute pressure / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If 50 kPa (0.5 kgf/cm2, 7 psi) is displayed for absolute pressure or -50 kPa (-0.5 kgf/cm2, -7 psi) is displayed for relative pressure, data has not been received.* |
| Result | Proceed to |
| Tire pressure values are not displayed. | A |
| All tire pressure readings are equal to specified values. | B |
|
| ||||
| A | ||
| ||