Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1241    Low Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.
The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No.
DTC Detection Condition
Trouble Area
C1241
Any of the following is detected:
  1. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.
  2. The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.
  3. The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.*
  4. The +BS terminal voltage is less than 6.7 V and the skid control ECU judges that power supply voltage is abnormal for 0.06 seconds or more.
  1. ABS NO. 2 fuse
  2. Battery
  3. Charging system
  4. Power source circuit
  5. Ground circuit
  6. Internal power supply circuit of the skid control ECU
*: The skid control ECU monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

WIRING DIAGRAM


C249037E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V


    Result:

    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C238832E17
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-25 (+BS) - Body ground
    Always
    11 to 14 V
    A49-25 (+BS) - A49-38 (GND1)
    Always
    11 to 14 V
    A49-28 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A49-28 (IG1) - A49-38 (GND1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))

    Result:

    Result
    Proceed to
    OK
    A
    NG (for +BS circuit)
    B
    NG (for IG1 circuit)
    C



B
Go to step 5

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
A


3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C238832E02
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-38 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


4.RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1241 is not output.
    A
    DTC C1241 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the engine room relay block and junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-25 (+BS) - 1I-1
    Always
    Below 1 Ω

    HINT:
    1. Even if the resistance between the skid control ECU and the engine room relay block and junction block assembly is normal, there may be an abnormality in the resistance of the wiring between the battery and the engine room relay block and junction block assembly. Therefore, be sure to inspect the circuit between the battery and the engine room relay block and junction block assembly before replacing the skid control ECU (brake actuator assembly).
    2. If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE WIRE HARNESS OR ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)