ENGINE ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Turn the A/C switch on.
Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.
Turn the ignition switch off.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. DISCHARGE FUEL SYSTEM PRESSURE |
| 4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 5. SECURE STEERING WHEEL |
| 6. REMOVE FRONT WHEELS |
| 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 8. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 9. REMOVE ENGINE UNDER COVER LH |
| 10. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 11. REMOVE ENGINE UNDER COVER RH |
| 12. REMOVE FRONT FENDER APRON SEAL LH |
| 13. REMOVE FRONT FENDER APRON SEAL RH |
| 14. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Clean the oil pan drain plug and install a new gasket and the oil pan drain plug.
| 15. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.

| *1 | Radiator Cap Sub-assembly | *2 | Radiator Drain Cock Plug |
| 16. DRAIN AUTOMATIC TRANSAXLE FLUID |
Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.
![]() |
Remove the refill plug and gasket from the automatic transaxle assembly.
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Overflow Plug |
| *3 | Hexagon Socket Wrench |
![]() |
Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle assembly.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
Drain automatic transaxle fluid from the automatic transaxle assembly.
![]() |
Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle assembly.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
![]() |
Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle assembly.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Overflow Plug |
| *3 | Hexagon Socket Wrench |
![]() |
Install a new gasket and the refill plug to the automatic transaxle assembly.
| 17. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 7 clips and cool air intake duct seal.
| 18. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the engine cover.
| 19. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 20. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the vacuum switching valve assembly from the air cleaner hose.
![]() |
Disconnect the mass air flow meter connector and 2 wire harness clamps from the air cleaner cap sub-assembly.
![]() |
Separate the fuel vapor feed hose from the air cleaner hose.
![]() |
Disconnect the ventilation hose from the cylinder head cover.
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
| 21. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
| 22. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Disconnect the wire harness clamp.
Remove the 2 bolts and air cleaner case sub-assembly.
| 23. REMOVE BATTERY |
![]() |
Loosen the nut, and separate the positive (+) battery terminal.
Loosen the nut, and remove the bolt and battery clamp.
Remove the battery and battery tray.
| 24. DISCONNECT NO. 1 RADIATOR HOSE |
![]() |
Remove the hose clamp to separate the air fuel ratio sensor wire from the No. 1 radiator hose.
Disconnect the No. 1 radiator hose.
| 25. DISCONNECT NO. 2 RADIATOR HOSE |
![]() |
Disconnect the No. 2 radiator hose.
| 26. DISCONNECT INLET HEATER WATER HOSE |
![]() |
Disconnect the inlet heater water hose.
| 27. DISCONNECT OUTLET HEATER WATER HOSE |
![]() |
Disconnect the 3 outlet heater water hoses.
| 28. REMOVE STARTER ASSEMBLY |
![]() |
Disconnect the starter connector.
Open the terminal cap, remove the nut and disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 29. DISCONNECT ENGINE WIRE |
Remove the No. 1 relay block cover.
![]() |
Remove the 2 nuts and disconnect the wire clamp.
Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.
![]() |
Disconnect the 4 connectors.
Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.
![]() |
Pull up the lever to disconnect the ECM connector.
Disconnect the 2 wire clamps.
| 30. DISCONNECT NO. 1 AIR CLEANER BRACKET |
![]() |
Disconnect the 2 wire clamps.
Remove the bolt and No. 1 air cleaner bracket.
| 31. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut and disconnect the transmission control cable from the control shaft lever.
![]() |
Remove the clip and disconnect the transmission control cable assembly from the No. 1 control cable bracket.
| 32. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Remove the 2 bolts and No. 2 engine mounting stay RH.
| 33. SEPARATE EARTH WIRE |
![]() |
Remove the bolt and separate the earth wire from the engine moving control rod bracket.
| 34. REMOVE ENGINE MOVING CONTROL ROD BRACKET |
![]() |
Remove the 4 bolts and engine moving control rod bracket.
| 35. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the bolt and engine moving control rod from the engine moving control rod bracket.
| 36. DISCONNECT UNION TO CONNECTOR TUBE HOSE |
![]() |
Disconnect the union to connector tube hose.
| 37. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the bolt.
Disconnect the 2 connectors.
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor assembly with pulley.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
| 38. DISCONNECT SUCTION HOSE SUB-ASSEMBLY (for TMMK Made) |
![]() |
Remove the bolt and disconnect the suction hose sub-assembly from the compressor assembly with pulley.
Remove the O-ring from the suction hose sub-assembly.
| 39. DISCONNECT NO.1 COOLER REFRIGERANT SUCTION HOSE (for SIA Made) |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose from the compressor assembly with pulley.
Remove the O-ring from the No. 1 cooler refrigerant suction hose.
| 40. DISCONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Release the claw and remove the No. 1 fuel pipe clamp.
Pinch the fuel tube connector and then pull out the fuel main tube.
| 41. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts, 2 compression springs.
Remove the front exhaust pipe assembly from the exhaust pipe support.
Remove the gasket from the exhaust manifold converter sub-assembly.
| 42. REMOVE FRONT AXLE SHAFT NUT LH |
![]() |
Using SST and a hammer, release the staked part of the front axle shaft nut.
While applying the brakes, remove the front axle shaft nut.
| 43. REMOVE FRONT AXLE SHAFT NUT RH |
| 44. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.
| 45. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 46. SEPARATE FRONT SPEED SENSOR LH |
![]() |
Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.
![]() |
Remove the bolt and front speed sensor from the steering knuckle.
| 47. SEPARATE FRONT SPEED SENSOR RH |
| 48. SEPARATE TIE ROD ASSEMBLY LH |
![]() |
Remove the cotter pin and nut.
![]() |
Install SST to the tie rod assembly LH.
Secure SST using a string.
Using SST, separate the tie rod assembly LH from the steering knuckle.

| *1 | Center Nut | - | - |
| *a | String | *b | Grease Application Area |
![]() | Place the wrench here. | - | - |
| 49. SEPARATE TIE ROD ASSEMBLY RH |
| 50. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.
| 51. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 52. SEPARATE FRONT AXLE ASSEMBLY LH |
![]() |
Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
| *a | Matchmark |
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.
| 53. SEPARATE FRONT AXLE ASSEMBLY RH |
| 54. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the steering intermediate shaft assembly and steering link assembly.
| *a | Matchmark |
Remove the bolt.
Separate the steering intermediate shaft assembly from the steering link assembly.
| 55. REMOVE FLYWHEEL HOUSING UNDER COVER |
![]() |
Remove the flywheel housing under cover.
| 56. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
![]() |
Turn the crankshaft to gain access to the removal locations of the 6 torque converter setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.
| 57. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
![]() |
Set the engine lifter.
![]() | Attachment Installation Position |
![]() |
Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.
Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.
Operate the engine lifter and remove the engine assembly from the vehicle.
Install engine hangers .
| 58. REMOVE ENGINE WIRE |
Remove the engine wire from the engine with transaxle.
| 59. REMOVE V-RIBBED BELT |
![]() |
Attach a wrench to the hexagonal portion of the belt tensioner as shown in the illustration, rotate the belt tensioner clockwise, and remove the V-ribbed belt.
| 60. REMOVE COMPRESSOR ASSEMBLY WITH PULLEY |
![]() |
Remove the 2 bolts and 2 nuts.
![]() |
Using an E8 "TORX" socket, remove the 2 stud bolts and compressor assembly with pulley.
| 61. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the generator connector.
Remove the terminal cap.
Remove the nut and disconnect the generator wire.
Remove the bolt and wire harness clamp bracket.
![]() |
Remove the 2 bolts and generator.
| 62. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the front drive shaft assembly LH.
| 63. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH |
![]() |
Using a screwdriver, remove the front drive shaft hole snap ring LH.
| 64. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.
| 65. REMOVE FRONT FRAME ASSEMBLY |
![]() |
Remove the nut and separate the engine mounting insulator LH.
![]() |
Remove the bolt and separate the front engine mounting insulator.
![]() |
Remove the nut and separate the engine mounting insulator RH.
Remove the front frame assembly.
Using a height adjustable attachment and plate lift attachment, place the engine assembly on a flat level surface.
| 66. REMOVE FRONT ENGINE MOUNTING INSULATOR |
![]() |
Remove the 3 nuts and front engine mounting insulator.
| 67. REMOVE ENGINE MOUNTING INSULATOR LH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator LH.
| 68. REMOVE ENGINE MOUNTING INSULATOR RH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator RH.
| 69. REMOVE DRIVE SHAFT BEARING BRACKET |
![]() |
Remove the 3 bolts and drive shaft bearing bracket.
| 70. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 3 bolts and engine mounting bracket RH.
| 71. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY |
Using the transmission jack attachment, set the automatic transaxle assembly on a transmission jack.
![]() |
Remove the 9 bolts and automatic transaxle assembly.
| 72. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts, front drive plate spacer, drive plate and ring gear sub-assembly, and rear drive plate spacer.
| 73. INSTALL ENGINE STAND |
Install the engine onto an engine stand with the bolts.