DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) |
DTC P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) |
DTC P0390 Camshaft Position Sensor "B" Circuit (Bank 2) |
DTC P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2) |
DTC P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 P0390 | No exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). |
|
| P0367 P0392 | The output voltage of the exhaust VVT sensor (bank 1, 2) is less than 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0368 P0393 | The output voltage of the exhaust VVT sensor (bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|

| ECM Terminal Name | Between NE+ and NE- Between EV1+ and EV1- Between EV2+ and EV2- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Related DTCs | P0365: Exhaust VVT sensor (bank 1) verify pulse input P0367: Exhaust VVT sensor (bank 1) range check (low voltage) P0368: Exhaust VVT sensor (bank 1) range check (high voltage) P0390: Exhaust VVT sensor (bank 2) verify pulse input P0392: Exhaust VVT sensor (bank 2) range check (low voltage) P0393: Exhaust VVT sensor (bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT sensor (for exhaust camshaft) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: P0367 and P0392 (Exhaust VVT sensor (bank 1, 2) range check [low voltage]) P0368 and P0393 (Exhaust VVT sensor (bank 1, 2) range check [high voltage]) 5 seconds: P0365 and P0390 (Exhaust VVT sensor verify pulse input) |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Engine speed | 600 rpm or higher |
| Starter | Off |
| Exhaust VVT sensor range check fail (P0367, P0368, P0392, P0393) | Not detected |
| Exhaust VVT sensor voltage | 0.3 to 4.7 V |
| Battery voltage | 8 V or higher |
| Engine switch | On (IG) |
| All of the following conditions are met | - |
| Starter | Off |
| Engine switch | On (IG) |
| Time after engine switch off to on (IG) | 2 seconds or more |
| Exhaust VVT sensor pulse input fail (P0365, P0390) | Not detected |
| Battery voltage | 8 V or higher |
| Exhaust VVT sensor signal | No signal |
| Exhaust VVT sensor voltage | Less than 0.3 V |
| Exhaust VVT sensor voltage | Higher than 4.7 V |
| Exhaust VVT sensor voltage | 0.3 to 4.7 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR EXHAUST CAMSHAFT)) |
![]() |
Disconnect the VVT sensor (for exhaust camshaft) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E53-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| E59-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| *1 | Bank 1 |
| *2 | Bank 2 |
| *a | Front view of wire harness connector (to VVT Sensor (for Exhaust Camshaft)) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM) |
Disconnect the VVT sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E53-1 (EX+) - E26-79 (EV1+) | Always | Below 1 Ω |
| E53-2 (EX-) - E26-110 (VV1-) | Always | Below 1 Ω |
| E59-1 (EX+) - E26-80 (EV2+) | Always | Below 1 Ω |
| E59-2 (EX-) - E26-110 (VV1-) | Always | Below 1 Ω |
| E53-1 (EX+) or E26-79 (EV1+) - Body ground | Always | 10 kΩ or higher |
| E53-2 (EX-) or E26-110 (VV1-) - Body ground | Always | 10 kΩ or higher |
| E59-1 (EX+) or E26-80 (EV2+) - Body ground | Always | 10 kΩ or higher |
| E59-2 (EX-) or E26-110 (VV1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST CAMSHAFT)) |
![]() |
Check the VVT sensor (for exhaust camshaft) installation.
|
| ||||
| OK | |
| 4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the exhaust camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assemblies RH and LH (Click here).
Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
|
| ||||
| OK | |
| 6.REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT) |
Replace the VVT sensor (for exhaust camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 OR P0393) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0365, P0367, P0368, P0390, P0392 or P0393 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM) |
Disconnect the VVT sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E53-3 (VC2) - E26-111 (VCV1) | Always | Below 1 Ω |
| E59-3 (VC2) - E26-111 (VCV1) | Always | Below 1 Ω |
| E53-3 (VC2) or E26-111 (VCV1) - Body ground | Always | 10 kΩ or higher |
| E59-3 (VC2) or E26-111 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||