Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Audio Receiver Assembly Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Audio Receiver Assembly Communication Stop Mode
Either condition is met:
  1. "Display and Navigation (AVN1)" is not displayed on the "CAN Bus Check" screen of the Techstream (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Radio and display receiver assembly branch line or connector
  2. Power source circuit of radio and display receiver assembly
  3. Radio and display receiver assembly ground circuit
  4. Radio and display receiver assembly*1
  1. *1: for Radio and Display Type w/o Intuitive Parking Assist System

WIRING DIAGRAM


C250688E01


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240580E10
  1. Disconnect the radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-9 (CANH) - I155-10 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the radio and display receiver assembly connector.



    C241180E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-7 (GND1) - Body ground*1
    I134-20 (GND1) - Body ground*2
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

    *1: for 6 Speakers
    *2: for 10 Speakers
    Text in Illustration 
    *A
    for 6 Speakers
    *B
    for 10 Speakers
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)

  1. Connect the cable to the negative (-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I152-3 (ACC1) - Body ground*1
    I134-11 (ACC1) - Body ground*2
    Ignition switch ACC
    11 to 14 V
    I152-4 (+B1) - Body ground*1
    I134-1 (+B1) - Body ground*2
    Always
    11 to 14 V
    I155-1 (IG) - Body ground
    ignition switch ON
    11 to 14 V

    *1: for 6 Speakers
    *2: for 10 Speakers



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)