Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly RH (for rear RH door) is operated by the power window regulator switch assembly (for rear RH door).

WIRING DIAGRAM


B246035E16


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) - BATTERY)
  1. Disconnect the power window regulator switch assembly (for rear RH door) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L6-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR)


    B164433E19
  1. Remove the power window regulator switch assembly (for rear RH door) (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    3 (B) - 4 (U)
    Below 1 Ω
    1 (D) - 2 (SD)
    off
    Below 1 Ω
    4 (U) - 5 (SU)
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Switch Assembly (for Rear RH Door))



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR RH DOOR) - POWER WINDOW REGULATOR MOTOR RH)
  1. Disconnect the power window regulator motor assembly RH (for rear RH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-4 (U) - L5-1 (U)
    Always
    Below 1 Ω
    L6-1 (D) - L5-2 (D)
    Always
    Below 1 Ω
    L6-4 (U) - Body ground
    Always
    10 kΩ or higher
    L6-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B164359E74
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (B) - 10 (U)
    UP
    Below 1 Ω
    1 (E) - 18 (D)
    Below 1 Ω
    1 (E) - 10 (U)
    off
    Below 1 Ω
    1 (E) - 18 (D)
    Below 1 Ω
    6 (B) - 18 (D)
    DOWN
    Below 1 Ω
    1 (E) - 10 (U)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR RH DOOR)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-10 (U) - L6-5 (SU)
    Always
    Below 1 Ω
    K11-18 (D) - L6-2 (SD)
    Always
    Below 1 Ω
    K11-10 (U) - Body ground
    Always
    10 kΩ or higher
    K11-18 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR REAR RH DOOR) (Click here)