Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly RH (for front passenger door) is operated by the power window regulator switch assembly (for front passenger door).

WIRING DIAGRAM


B246037E09


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR) - BATTERY)
  1. Disconnect the power window regulator switch assembly (for front passenger door) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J11-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR)


    B164433E19
  1. Remove the power window regulator switch assembly (for front passenger door) (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    3 (B) - 4 (U)
    Below 1 Ω
    1 (D) - 2 (SD)
    off
    Below 1 Ω
    4 (U) - 5 (SU)
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Switch Assembly (for Front Passenger Door))



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR FRONT PASSENGER DOOR) - POWER WINDOW REGULATOR MOTOR RH)
  1. Disconnect the power window regulator motor assembly RH (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J11-4 (U) - J14-2 (U)
    Always
    Below 1 Ω
    J11-1 (D) - J14-1 (D)
    Always
    Below 1 Ω
    J11-4 (U) - Body ground
    Always
    10 kΩ or higher
    J11-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B164359E72
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (B) - 16 (U)
    UP
    Below 1 Ω
    1 (E) - 15 (D)
    Below 1 Ω
    1 (E) - 16 (U)
    off
    Below 1 Ω
    1 (E) - 15 (D)
    Below 1 Ω
    6 (B) - 15 (D)
    DOWN
    Below 1 Ω
    1 (E) - 16 (U)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR FRONT PASSENGER DOOR))
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-16 (U) - J11-5 (SU)
    Always
    Below 1 Ω
    K11-15 (D) - J11-2 (SD)
    Always
    Below 1 Ω
    K11-16 (U) - Body ground
    Always
    10 kΩ or higher
    K11-15 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR FRONT PASSENGER DOOR) (Click here)