FRONT DOOR > DISASSEMBLY |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.
| 4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish.
| 5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.
| 6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.
| 7. REMOVE FRONT ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.
| 8. REMOVE COURTESY LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *A | for LH Side |
| *B | for RH Side |
| *1 | Protective Tape |
Disconnect the connector and remove the courtesy light assembly.
| 9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the front door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 10 clips.
![]() |
Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Front Door Inner Glass Weatherstrip |
Disengage the reference boss from the front door panel.
Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
![]() |
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
| 10. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.
| 11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 12. REMOVE DOOR SIDE AIRBAG SENSOR |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Disconnect the connector from the door side airbag sensor.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connector Lock is Released | - | - |
Push down the white housing lock again and disconnect the connector.
![]() |
Remove the bolt and door side airbag sensor from the front door panel.
After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |
| 13. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 4 screws.
![]() |
Disengage the 2 claws and remove the front No. 1 speaker assembly.
| 14. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 bolts.
Disengage the claw and remove the outer rear view mirror assembly.
| 15. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Remove the bolt.
Disconnect each connector.
Disengage the 5 clamps.
Remove the front door service hole cover.
| 16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the grommet.
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
| 17. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
| 18. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.
| 19. REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION |
![]() |
Remove the 2 bolts.
| *1 | Double-sided Tape |
Disengage the 2 guides and remove the No. 2 front door stiffener cushion.
| 20. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 21. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts.
Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.
| 22. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts.
Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.
| 23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side) |
w/ Front Door Lock Cylinder:
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) |
![]() |
Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.
| 26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) |
w/ Front Door Lock Cylinder:
w/o Front Door Lock Cylinder:
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
| 27. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
w/ Smart Key System:
Disengage the 2 claws.
![]() |
Using a screwdriver, disconnect the connector.
![]() |
Remove the front door outside handle assembly as shown in the illustration.
| 28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Disengage the 3 claws and remove the front door front outside handle pad.
| 29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Disengage the 2 claws and remove the front door rear outside handle pad.
| 30. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY |
![]() |
Using a T30 "TORX" socket wrench, remove the 3 screws.
| *1 | Front Door Lock Open Rod |
Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.
When reusing the front door lock with motor assembly:
![]() |
Remove the door lock wiring harness seal from the front door lock with motor assembly.
| 31. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Remove the front door lock remote control cable assembly.
| 32. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws.
![]() |
Remove the front door inside locking cable assembly.
| 33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
w/ Smart Key System:
![]() |
Disconnect the connector.
Disengage the 3 clamps.
![]() |
Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.
| 34. REMOVE FRONT DOOR WIRE (w/ Smart Key System) |
![]() |
Disengage the 3 clamps and remove the front door wire.
| 35. REMOVE FRONT DOOR LOCK OPEN ROD |
![]() |
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
| 36. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts and front door check assembly.
| 37. REMOVE FRONT DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.
| 38. REMOVE DOOR FRAME GARNISH |
![]() |
Disengage the clip and remove the door frame garnish.
| 39. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.
| 40. REMOVE FRONT DOOR PANEL CUSHION |
![]() |
Disengage the 2 claws and remove the 2 front door panel cushions.
| 41. REMOVE DOOR DUST PROOF SEAL |
![]() |
Remove the door dust proof seal.
| 42. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Put protective tape around the front door belt moulding assembly.
| *1 | Protective Tape |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the front door belt moulding assembly.
| *1 | Protective Tape |
| 43. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Using a heat light, heat the front door rear window frame moulding.
![]() |
Using a moulding remover, disengage the clip and remove the front door rear window frame moulding.
| *1 | Double-sided Tape |
| *2 | Caulking Sponge |
| 44. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING |
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
![]() |
Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Dimension |
| A | 5.0 mm |
Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.
| 45. REMOVE FRONT DOOR STRIPE |
Using a heat light, heat the front door stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Front Door Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door stripe to remove it.
| 46. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE |
Using a heat light, heat the front door lower outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Front Door Rear Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door lower outside stripe to remove it.