Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > SYSTEM DESCRIPTION

for Preparation Click here



WIRELESS DOOR LOCK CONTROL SYSTEM
The wireless door lock control system functions to lock and unlock all the doors from a distance. The system is controlled by a door control transmitter module set sub-assembly which sends radio waves to the door control receiver. The main body ECU (multiplex network body ECU) performs an ID code identification process and engages the door lock control.

MULTI CHANNEL FUNCTION
The wireless door lock control system has a multi-channel function. Each time the switch on the electrical key transmitter is pressed, the channel is switched alternately between 2 different frequencies and the signal is sent to the door control receiver.*
  1. *: w/ Tire Pressure Warning System

FUNCTION OF MAIN COMPONENTS

Component
Function
Door control transmitter module set sub-assembly
  1. Has lock, unlock, luggage open and panic switches.
  2. Transmits weak radio waves (recognition codes and function codes) to the door control receiver.
  3. Illuminates the indicator light (LED) during transmission.*
Door control receiver
Receives weak radio waves from the door control transmitter module set sub-assembly and sends them to the main body ECU (multiplex network body ECU).
  1. Front door courtesy light switch assembly LH/RH
  2. Rear door courtesy light switch assembly LH/RH
  3. Luggage door courtesy light switch
  1. Turns on when a door is opened and turns off when it is closed.
  2. Outputs door status signals (open or closed) to the main body ECU (multiplex network body ECU).
Unlock warning switch assembly
Detects if the key is inserted in the ignition key cylinder or not.
  1. Front door lock with motor assembly LH/RH
  2. Rear door lock with motor assembly LH/RH
  1. Built in motor locks or unlocks door.
  2. Transmits the door lock position of each door to the main body ECU (multiplex network body ECU)
Main body ECU (multiplex network body ECU)
Sends wireless door lock control signals in response to the code data from the door control receiver and signals from each switch.
  1. *: w/o Tire Pressure Warning System

SYSTEM FUNCTION
The door control transmitter module set sub-assembly has the lock, unlock, luggage door open and panic switches. Operating these switches activates each function.
The wireless door lock control system has the following functions:

HINT:
The default settings of the following functions are on. Part of these functions can be customized (Click here).


Function
Operation
All door lock
Pressing the lock switch locks all doors.
All door unlock
(Unlock 2 operation)
Pressing the unlock switch twice within 5 seconds unlocks all the doors after the driver door is unlocked.
Luggage compartment door open
Pressing the luggage door open switch of the door control transmitter module set sub-assembly for longer than about 0.8 seconds opens the luggage compartment door.
Automatic lock
If none of the doors is opened within 60 seconds after they are unlocked by wireless door lock control, all the doors will lock again automatically.
Answer back (Hazard warning light)
  1. When the doors are locked by wireless operation, the hazard warning lights flash once.
  2. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
Answer back (Wireless door lock buzzer)
  1. When the doors are locked by wireless operation, the wireless door lock buzzer sounds once.
  2. When the doors are unlocked by wireless operation, the wireless door lock buzzer sounds twice.
  3. When the luggage compartment door is opened by wireless operation, the wireless door lock buzzer sounds.
Panic alarm
Pressing the panic switch of the door control transmitter module set sub-assembly for longer than about 0.8 seconds causes the following alarms to activate:
  1. Sound the vehicle horns.
  2. Blinks the headlights, hazard warning lights and taillights.
  3. Illuminates the interior lights (when the No. 1 room light assembly switch in DOOR position).*1
  4. Illuminates the interior lights (when the interior light door switch on).*2
While the panic alarm is operating, pressing any switch of the door control transmitter module set sub-assembly cancels the alarm operation.
Door ajar warning
The buzzer sounds when the lock switch is pressed when any of the doors are ajar, and it sounds for 5 seconds continuously. The buzzer stops when all doors are closed or the unlock switch is pressed.
Illuminated entry
When all the doors are locked, pressing the unlock switch causes the interior lights to come on simultaneously with the unlock operation.
Self-diagnostic mode
The following are conditions to enter self-diagnostic mode:
  1. If the door control receiver receives normal radio waves from the door control transmitter module set sub-assembly when the system is in diagnostic mode, it flashes the interior lights and sounds the wireless door lock buzzer in a normal pattern that corresponds to the function of each switch.
Transmitter recognition code registration
Enables registration (writing and storing) of door control transmitter module set sub-assembly recognition codes in the EEPROM that is contained in the door control receiver.
  1. *1: w/o Sliding Roof
  2. *2: w/ Sliding Roof

TRANSMITTER RECOGNITION CODE REGISTRATION FUNCTION
The table below shows the 4 ID registration function modes. The codes are electronically registered (written and stored) in the EEPROM that is contained in the door control receiver.

Mode
Function
Add mode
Adds a newly received code while preserving any previously registered codes.
This mode is used when adding a new door control transmitter module set sub-assembly. If the maximum registration number is exceeded, the oldest one is cleared first.
Rewrite mode
Clears all previously registered codes and registers only newly input codes.
Confirmation mode
Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.
Prohibition mode
Deletes all registered codes and disables the wireless door lock function.
This mode is used when the door control transmitter module set sub-assembly is lost.

CONDITIONS THAT WIRELESS FUNCTIONS DO NOT OPERATE
  1. Lock function will not operate when either of the following conditions is met:

    1. Any of the doors is open.
    2. The key is inserted in the ignition key cylinder.

  2. Unlock function will not operate when the following condition is met:

    1. The key is inserted in the ignition key cylinder.