Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0451
Canister pressure sensor abnormal voltage fluctuation
Sensor output voltage fluctuates frequently in a certain time period.
  1. Canister pump module
  2. Connector/wire harness
    (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
  1. EVAP monitoring (engine switch off)
  2. Engine running
2 trip
Canister pressure sensor constant voltage
Sensor output voltage does not vary in a certain time period.
  1. EVAP monitoring (engine switch off)
2 trip
P0452
Canister pressure sensor low input
EVAP pressure sensor less than 42.11 kPa(abs) [315.867 mmHg(abs)] for 0.5 seconds.
  1. Engine switch on (IG)
  2. EVAP monitoring (engine switch off)
1 trip
P0453
Canister pressure sensor high input
EVAP pressure sensor higher than 123.761 kPa(abs) [928.331 mmHg(abs)] for 0.5 seconds.
  1. Engine switch on (IG)
  2. EVAP monitoring (engine switch off)
1 trip

HINT:
The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System .

MONITOR DESCRIPTION


A115543E70

  1. DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant
    If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC.
    Alternatively, if the sensor voltage output does not change for 2 minutes, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC.
    (Both the malfunctions are detected by 2 trip detection logic).
  2. DTC P0452: Canister pressure sensor voltage low
    If the canister pressure sensor voltage output (pressure) is less than 0.45 V: 42.11 kPa(abs) [315.867 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
  3. DTC P0453: Canister pressure sensor voltage high
    If the canister pressure sensor voltage output (pressure) is higher than 4.9 V: 123.761 kPa(abs) [928.331 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components (Main)
Canister pump module
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds: P0452 and P0453
Within 2 minutes: P0451 (stuck monitoring)
Less than 15 seconds: P0451 (noise monitoring)
MIL Operation
Immediate: P0452 and P0453
2 driving cycles: P0451
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0451 (Noise Monitoring) 
Atmospheric pressure (absolute pressure)
70 kPa(abs) [525 mmHg(abs)] or higher, and less than 110 kPa(abs) [825 mmHg(abs)]
Battery voltage
10.5 V or higher
Intake air temperature
4.4°C (40°F) or higher, and less than 35°C (95°F)
Canister pressure sensor malfunction (P0452, P0453)
Not detected
Either of the following conditions is met
A or B
A. Engine condition
Running
B. Time after key-off
5, 7 or 9.5 hours

P0451 (Stuck Monitoring) 
Battery voltage
10.5 V or higher
Intake air temperature
4.4°C (40°F) or higher, and less than 35°C (95°F)
Canister pressure sensor malfunction (P0452, P0453)
Not detected
Atmospheric pressure (absolute pressure)
Less than 70 kPa(abs) [525 mmHg(abs)], or 110 kPa(abs) [825 mmHg(abs)] or higher
Time after key-off
5, 7 or 9.5 hours

P0452 and P0453 
Engine switch
On (IG)
Battery voltage
8 V or higher
Starter
Off

TYPICAL MALFUNCTION THRESHOLDS


P0451: Canister Pressure Sensor Noise Monitoring 
Frequency that EVAP pressure change 0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher
10 times or more in 10 seconds

P0451: Canister Pressure Sensor Stuck Monitoring 
EVAP pressure change during reference pressure measurement
Less than 0.65 kPa(gauge) [4.876 mmHg(gauge)]

P0452: Canister Pressure Sensor Low Voltage 
EVAP pressure
Less than 42.11 kPa(abs) [315.867 mmHg(abs)]

P0453: Canister Pressure Sensor High Voltage 
EVAP pressure
Higher than 123.761 kPa(abs) [928.331 mmHg(abs)]

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature less than 35°C (95°F).

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Enter the following menus: Powertrain / Engine / Data List / Intake Air.
  4. Check that the intake air temperature is between 4.4 and 35°C (40 and 95°F).
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Turn the engine switch off and wait for at least 30 seconds.
  7. Turn the engine switch on (IG) and turn the Techstream on.
  8. Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.
  9. After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.
  10. Input the DTC: P0451, P0452 or P0453.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A255674E02


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
  2. The Techstream is required to conduct the following diagnostic troubleshooting procedure.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG) (do not start the engine).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

  1. Enter the following menus: Powertrain / Engine / Data List / Gas Evaporative / Vapor Pressure Pump.

  1. Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

    Result 
    Display (DTC Output)
    Test Result
    Suspected Trouble Area
    Proceed to
    P0451
    -
    Canister pressure sensor
    C
    P0452
    Less than 42.11 kPa(abs) [315.867 mmHg(abs)]
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Short in ECM circuit
    A
    P0453
    Higher than 123.761 kPa(abs) [928.331 mmHg(abs)]
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Canister pressure sensor
    3. Open in ECM circuit
    B



B
Go to step 4

C
GO TO EVAP SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    A25-42 (PPMP) - Body ground
    Always
    Below 10 Ω
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in canister pressure sensor circuit
    A
    10 kΩ or higher
    1. Wire harness/connector (ECM - canister pressure sensor)
    2. Short in ECM circuit
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    A25-42 (PPMP) - Body ground
    Always
    10 kΩ or higher
    Short in canister pressure sensor circuit
    A
    Below 10 Ω
    Short in wire harness/connector (ECM - canister pressure sensor)
    B



A
Go to step 5

B
Go to step 6

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)


  1. Disconnect the canister pump module connector.


    A255701E11


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Canister Pump Module)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    N35-8 (SGND) - Body ground
    Always
    100 Ω or less

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    N35-6 (VCC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V
    N35-7 (VOUT) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V


    Result 
    Test Result
    Suspected Trouble Area
    Proceed to
    Voltage and resistance within standard ranges
    Open in canister pressure sensor circuit
    A
    Voltage and/or resistance outside standard ranges
    Open in wire harness/connector (ECM - canister pressure sensor)
    B



B
Go to step 6
A


5.REPLACE CANISTER PUMP MODULE


  1. Replace the canister pump module (Click here).

    NOTICE:
    1. When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace canister and canister pump module together.
    2. Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace canister and the canister pump module together.
    3. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.


    A256013E02


    Text in Illustration 
    *1
    Fuel Tank Vent Hose
    *2
    Air Inlet Port
    *3
    Vent Hose
    *4
    Fuel Tank
    *5
    Canister Pump Module
    *6
    Canister
    *7
    Canister Filter
    -
    -
    *a
    Inspection Area (Check for disconnection and/or cracks)
    -
    -



NEXT
Go to step 8

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

HINT:
If the exhaust pipe has been removed, go to the next step before reinstalling it.



NEXT
Go to step 8

7.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Perform the Evaporative System Check using the Techstream, referring to the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P0451, P0452 or P0453.

  1. Check the DTC judgment result.

    Result 
    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END