Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Main Body ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Main Body ECU Communication Stop Mode
Either condition is met:
  1. "Main Body" is not displayed on the "CAN Bus Check" screen of the Techstream (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Main body ECU (Multiplex network body ECU) branch line or connector
  2. Power source circuit of Main body ECU (Multiplex network body ECU) or Instrument panel junction block assembly
  3. Main body ECU (Multiplex network body ECU) ground circuit or Instrument panel junction block assembly
  4. Main body ECU (Multiplex network body ECU) or Instrument panel junction block assembly

WIRING DIAGRAM


C245100E09


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 20 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240484E04
  1. Disconnect the main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I13-14 (CANH) - I13-13 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (MAIN BODY ECU)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C223282E08
  1. Disconnect the instrument panel junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-7 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Connect the cable to the negative (-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3D-31 (BECU) - Body ground
    Ignition switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.2 RELAY AND ACC RELAY)
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E191506E11


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3E-1 - MB-32 (IG)
    Always
    10 kΩ or higher
    3E-1 - MB-32 (IG)
    Battery positive (+) → 3A-27
    Battery negative (-) → 3B-7
    Below 1 Ω
    3E-1 - MB-29 (ACC)
    Always
    10 kΩ or higher
    3E-1 - MB-29 (ACC)
    Battery positive (+) → 3B-23
    Battery negative (-) → 3B-7
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)