Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E01

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated when the engine switch is turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM


A255770E03


A255771E03


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when the engine switch is turned on (IG).

    OK:
    MIL lights up.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK CONNECTION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Check the communication between the Techstream and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
A


5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
  1. Disconnect the VVT sensor (for intake camshaft of bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1) (Click here)
A


6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
  1. Disconnect the VVT sensor (for intake camshaft of bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2) (Click here)
A


7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))
  1. Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1) (Click here)
A


8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))
  1. Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2) (Click here)
A


9.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CANISTER PUMP MODULE (Click here)
A


10.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E16-5 (VC) or E26-126 (VCTA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A36-4 (VCPA) or A25-56 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A36-1 (VCP2) or A25-59 (VCP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT)
  1. Disconnect the VVT sensor (for intake camshaft of bank 1) connector.

  1. Disconnect the VVT sensor (for intake camshaft of bank 2) connector.

  1. Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.

  1. Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E26-111 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)