DTC B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1656/38 |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.
Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N32-2 (LBE+) - N32-1 (LBE-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N32-2 (LBE+) - N32-1 (LBE-) | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N32-2 (LBE+) - Body ground | Ignition switch ON | Below 1 V |
| N32-1 (LBE-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N32-2 (LBE+) - Body ground | Always | 1 MΩ or higher |
| N32-1 (LBE-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK DTC |
![]() |
Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||
| 7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat inner belt assembly LH with a known good one (Click here for Manual Seat, Click here for Power Seat).
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK (for Manual Seat) | A |
| OK (for Power Seat) | B |
| NG | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Restore the front seat inner belt assembly LH that was installed for testing to its original location (Click here for Manual Seat, Click here for Power Seat).
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||