Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING

FRONT DOOR WINDOW FRAME MOULDING > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
(Click here)


4. REMOVE DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Disconnect the connector from the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


      H043302E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connector Lock is Released
      -
      -

    2. Push down the white housing lock again and disconnect the connector.

      NOTICE:
      Do not push down the part (A) shown in the illustration when disconnecting.



    B278819
  1. Remove the bolt and door side airbag sensor from the front door panel.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct



5. REMOVE FRONT DOOR SERVICE HOLE COVER


    B277198
  1. Remove the bolt.

  1. Disconnect each connector.

  1. Disengage the 5 clamps.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



6. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B277200
  1. Remove the grommet.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the power window regulator master switch assembly.



    B280340
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B280342E01
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.



7. REMOVE FRONT DOOR GLASS RUN


    B280345
  1. Remove the front door glass run.



8. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    B280066E01
  1. Put protective tape around the front door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B280067E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the front door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT DOOR CHECK ASSEMBLY


    B280375
  1. Remove the 3 bolts and front door check assembly.



10. REMOVE FRONT DOOR WEATHERSTRIP


    B280376
  1. Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.



11. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or moulding excessively.

  1. Using a heat light, heat the front door rear window frame moulding.



    B280095E01
  1. Using a moulding remover, disengage the clip and remove the front door rear window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape
    *2
    Caulking Sponge



12. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B280100E01
  1. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
    Area
    Dimension
    A
    5.0 mm

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.