Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.

  1. Remove the ignition coils and spark plugs (Click here).



    A133895
  1. Disconnect the 6 fuel injector connectors.



    A133897
  1. Install the spark plug into the ignition coil, and then connect the ignition coil connector.

  1. Ground the spark plug.

  1. Check that spark occurs at each spark plug while the engine is being cranked.

    NOTICE:
    1. Be sure to ground the spark plugs when checking them.
    2. Do not crank the engine for more than 2 seconds.
      Cranking will stop if the engine switch is pushed again for models with cranking holding function.
    3. If a spark plug has been struck or dropped, replace it.
    4. If an ignition coil has been struck or dropped, replace it.

    HINT:
    If spark does not occur for any cylinder, perform the following inspect Ignition Coil and Spark Test procedure.

  1. Connect the 6 fuel injector connectors.

  1. Install the spark plugs and ignition coils (Click here).

  1. Clear the DTCs (Click here).



2. INSPECT IGNITION COIL AND SPARK TEST

HINT:
Perform "Inspection After Repair" after replacing the spark plug (Click here).

  1. Check that the wire harness side connector of the ignition coil is securely connected.

    Result:
    Result
    Action
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil.

    1. Replace the ignition coil with a known good one.

    2. Perform the spark test again.

      Result:
      Result
      Action
      NG
      Go to next step
      OK
      Replace ignition coil

  1. Perform a spark test on each spark plug.

    1. Replace the spark plug with a known good one.

    2. Perform the spark test again.

      Result:
      Result
      Proceed to
      NG
      Inspect the ignition system (Click here).
      OK
      Replace spark plug



3. CHECK SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not adjust the electrode gap of a spark plug.

HINT:
Perform "Inspection After Repair" after replacing the spark plug (Click here).



    I039522E47
  1. Check the electrode using a megohmmeter.
    Text in Illustration 
    *1
    Ground

    1. Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (terminal part) - Body ground
      Always
      10 MΩ or more

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      2. If a megohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug (Click here).

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

    4. Install the spark plug (Click here).

  1. Check the spark plug for any damage to its threads and insulator.
    If there is any damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Spark Plug Type
    DENSO
    FK20HR11



  1. Reference.



      A175269
    1. Check the spark plug electrode gap.

      Maximum Electrode Gap for Used Spark Plug:
      1.4 mm (0.0551 in.)

      If the gap is greater than the maximum, replace the spark plug.

      NOTICE:
      Never attempt to adjust the gap of a used

      Electrode Gap for New Spark Plug:
      1.0 to 1.1 mm (0.0394 to 0.0433 in.)



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard Air Pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Standard Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.