Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1381    Acceleration Sensor Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the skid control ECU receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type).

DTC No.
DTC Detection Condition
Trouble Area
C1381
Vehicle speed is 6 km/h (4 mph) and yaw rate and acceleration sensor power supply malfunction signal is received for 1.1 seconds or more.
  1. Yaw rate and acceleration sensor power source circuit
  2. Yaw rate and acceleration sensor (for separate type)
  3. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)

WIRING DIAGRAM

Refer to DTCs C1234 and C1472 .

INSPECTION PROCEDURE

1.CONFIRM YAW RATE AND ACCELERATION SENSOR TYPE
  1. Confirm the yaw rate and acceleration sensor type.

    Result:

    Result
    Proceed to
    Yaw rate and acceleration sensor (for separate type)
    A
    Yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type)
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C249130E04
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I172-4 (IGA) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C249130E03
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I172-1 (GNDA) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor)

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C239271E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I47-21 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C239271E02
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I47-25 (E1) - Body ground
    Always
    Below 1 Ω
    I47-26 (E2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)