Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Power Steering ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Power Steering ECU Communication Stop Mode
Either condition is met:
  1. "Power Steering (EPS)" is not displayed on the "CAN Bus Check" screen of the Techstream (Click here)
  2. Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" (Click here)
  1. Power steering ECU assembly branch line or connector*1*3
  2. Power source circuit of power steering ECU assembly*1*3
  3. Power steering ECU assembly ground circuit*1*3
  4. Power steering ECU assembly*1*3
  5. Power steering ECU with motor assembly branch line or connector*2
  6. Power source circuit of power steering ECU with motor assembly*2
  7. Power steering ECU with motor assembly ground circuit*2
  8. Power steering ECU with motor assembly*2
*1: for 2GR-FE w/ wireless door lock system
*2: for 2AR-FE w/ wireless door lock system
*3: for 2AR-FE w/o wireless door lock system

WIRING DIAGRAM


C250224E04


C250224E05


C250224E06


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 10 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR VEHICLE TYPE
  1. Check for vehicle type.

    Result:
    Result
    Proceed to
    1. for 2GR-FE w/ wireless door lock system
    2. for 2AR-FE w/o wireless door lock system
    A
    for 2AR-FE w/ wireless door lock system
    B



B
Go to step 4
A


2.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240534E06
  1. Disconnect the power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 2AR-FE w/o Wireless Door Lock System):
    Tester Connection
    Condition
    Specified Condition
    j1-7 (CANH) - j1-8 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Standard Resistance (for 2GR-FE w/ Wireless Door Lock System):
    Tester Connection
    Condition
    Specified Condition
    j3-4 (CANH) - j3-8 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    for 2AR-FE w/o Wireless Door Lock System
    *2
    for 2GR-FE w/ Wireless Door Lock System
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C240535E07
  1. Disconnect the power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)

  1. Connect the cable to the negative (-) battery terminal.



    C240534E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for 2AR-FE w/o Wireless Door Lock System):
    Tester Connection
    Switch Condition
    Specified Condition
    j1-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Voltage (for 2GR-FE w/ Wireless Door Lock System):
    Tester Connection
    Switch Condition
    Specified Condition
    j3-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    for 2AR-FE w/o Wireless Door Lock System
    *2
    for 2GR-FE w/ Wireless Door Lock System
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)

Result:
Result
Proceed to
OK (for 2GR-FE w/ wireless door lock system)
A
OK (for 2AR-FE w/o wireless door lock system)
B
NG
C



B
REPLACE POWER STEERING ECU ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
A

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

4.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU WITH MOTOR ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C250229E03
  1. Disconnect the power steering ECU with motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 2AR-FE w/ Wireless Door Lock System):
    Tester Connection
    Condition
    Specified Condition
    j1-7 (CANH) - j1-8 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    for 2AR-FE w/ Wireless Door Lock System
    *a
    Front view of wire harness connector
    (to Power Steering ECU with motor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU WITH MOTOR ASSEMBLY)
OK


5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C240535E08
  1. Disconnect the power steering ECU with motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 2AR-FE w/ Wireless Door Lock System):
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

    Text in Illustration 
    *1
    for 2AR-FE w/ Wireless Door Lock System
    *a
    Front view of wire harness connector
    (to Power Steering ECU with Motor Assembly)

  1. Connect the cable to the negative (-) battery terminal.



    C250229E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for 2AR-FE w/ Wireless Door Lock System):
    Tester Connection
    Switch Condition
    Specified Condition
    j1-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    for 2AR-FE w/ Wireless Door Lock System
    *a
    Front view of wire harness connector
    (to Power Steering ECU with Motor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY (Click here)