Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER SUPPORT


    C242187E01
  1. Install the shift lever support with the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL LOWER SHIFT LEVER ASSEMBLY

NOTICE:
Check that the park/neutral position switch and the shift lever are in neutral.



    C244005E01
  1. Install the lower shift lever assembly with the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the 3 clamps and 2 connectors.



    C194520E03
  1. Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece
    *a
    Slide
    *b
    Pull



    C239661E01
  1. Install the transmission control cable end to the lower shift lever assembly.
    Text in Illustration 
    *1
    Lock Piece

    NOTICE:
    1. Check that the lock piece is pulled up.
    2. Install the cable end all the way to the base of the pin.

  1. Push the lock piece into the adjuster case.

    NOTICE:
    1. Check that the park/neutral position switch and the shift lever are in neutral.
    2. Securely push in the lock piece until the slider lock is engaged.



3. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)
  1. Install the clip and No. 1 console box duct.



4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET
  1. Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.



5. INSTALL FLOOR CARPET BRACKET LH
  1. Engage the 2 guides.

  1. Install the floor carpet bracket LH with the 2 clips.



6. INSTALL CONSOLE BOX INSERT


    B279902
  1. Engage the clip and 3 guides.

  1. Install the console box insert with the 2 screws <C> or <D>.



7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B280293
  1. Engage the clip and 3 guides.

  1. Install the front No. 2 console box insert with the 2 screws <C> or <D>.

  1. Engage the 2 claws to connect the room temperature sensor.



8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect each connector.

  1. Engage the 4 clips and guide.

  1. Install the upper console panel sub-assembly with the 2 screws <C> or <D>.



9. INSTALL BOX BOTTOM MAT
  1. Install the box bottom mat.



10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.



    B284909
  1. Engage the glove compartment light as shown in the illustration.



    B280313
  1. Engage the guide and 2 clips.

  1. Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.



11. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B279742E01
  1. Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

    Text in Illustration 
    *1
    Airbag Connector
    *2
    Airbag Connector Lock

  1. Push in the lock to install the airbag connector.

  1. Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.

  1. Install the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.



12. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.



13. INSTALL INSTRUMENT SIDE PANEL RH
  1. Engage the 3 guides.



    B279884
  1. Engage the 4 claws to install the instrument side panel RH as shown in the illustration.



14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B278981E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



15. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



16. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. Engage the 4 claws, 9 clips and 3 guides.

  1. Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.



18. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.



19. INSTALL INSTRUMENT SIDE PANEL LH
  1. Engage the 3 guides.



    B278009
  1. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.



20. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B278980E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



21. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the clip.



22. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 10 claws to install the front door scuff plate LH.



23. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



25. INSPECT SHIFT LEVER POSITION
  1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.



26. PERFORM DIAGNOSTIC SYSTEM CHECK
  1. for Built-in Type Yaw Rate Sensor: (Click here)
  2. for Separate Type Yaw Rate Sensor: (Click here)


27. INSPECT SRS WARNING LIGHT
  1. for Built-in Type Yaw Rate Sensor: (Click here)
  2. for Separate Type Yaw Rate Sensor: (Click here)