Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and air conditioning control assembly (passenger airbag ON/OFF indicator).
The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front passenger side knee airbag and front seat belt pretensioner RH.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1660/43
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit.
  2. Air conditioning control assembly malfunction
  3. Airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Air conditioning control assembly (Passenger airbag ON/OFF indicator)
  3. Airbag sensor assembly

WIRING DIAGRAM


C239224E05


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the Techstream (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    Result:
    ON/OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).



B
Go to step 9
A


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and air conditioning control assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and air conditioning control assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
  1. Connect the connector to the air conditioning control assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not come on.



NG
Go to step 5
OK


4.CHECK DTC


    C238328E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the connector to the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C240625E04
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect the connector from the air conditioning control assembly.

  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - I56-16 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK INSTRUMENT PANEL WIRE (SHORT)
C240626E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - I56-16 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C240626E05
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    I56-16 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C240626E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - Body ground
    Always
    1 MΩ or higher
    I56-16 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)  

9.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and air conditioning control assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and air conditioning control assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


10.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C240625E04
  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - I56-16 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


11.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C240626E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - I56-16 (P-AB)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


12.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C240626E05
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    I56-16 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


13.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C240626E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I56-8 (PAON) - Body ground
    Always
    1 MΩ or higher
    I56-16 (P-AB) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


14.CHECK AIR CONDITIONING CONTROL ASSEMBLY (SOURCE VOLTAGE)


    C240626E06
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I56-2 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Air Conditioning Control Assembly)



NG
REPLACE WIRE HARNESS OR BATTERY
OK


15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
C241739E04
  1. Connect the connector to the air conditioning control assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Check the indicator according to the conditions in the table below.

    OK:
    Terminal Connection
    Condition
    Specified Condition
    I47-23 (PAON) - Body ground
    Ignition switch ON
    "ON" comes on
    I47-17 (P-AB) - Body ground
    Ignition switch ON
    "OFF" comes on

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly
    *3
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)
OK


16.CHECK DTC


    C238328E01
  1. Connect the connector to the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Air Conditioning Control Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)