Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > ACIS Control Circuit

for Preparation Click here


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) according to the engine load in order to increase intake efficiency (ACIS: Acoustic Control Induction System).

A197286E02


WIRING DIAGRAM


A266359E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE VACUUM SWITCHING VALVE ASSEMBLY FOR ACIS)
A208635E02
  1. Disconnect the vacuum hose from port F of the vacuum switching valve assembly (for acoustic control induction system).

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control.

  1. Operate the vacuum switching valve assembly for acoustic control induction system.

  1. Check the vacuum switching valve assembly air flow when switching the vacuum switching valve assembly.

    OK:
    Test Condition
    Specified Condition
    Vacuum switching valve assembly is ON
    Air from port E flows out through port F
    Vacuum switching valve assembly is OFF
    Air from port E flows out through air filter

    Text in Illustration 
    *1
    Air
    *2
    Port F
    *3
    Port E
    *4
    Air Filter
    *a
    Vacuum Switching Valve Assembly is ON
    *b
    Vacuum Switching Valve Assembly is OFF



NG
Go to step 4
OK


2.CHECK VACUUM HOSES (VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS) - INTAKE AIR CONTROL VALVE, INTAKE MANIFOLD)
  1. Check the vacuum hoses (Click here).



NG
REPAIR OR REPLACE VACUUM HOSES
OK


3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE FOR ACIS)
  1. Inspect the intake air control valve (for acoustic control induction system) .



NG
REPLACE INTAKE MANIFOLD (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)
  1. Inspect the vacuum switching valve assembly (for acoustic control induction system) (Click here).



NG
REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS) (Click here)
OK


5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE ASSEMBLY)


    A194112E41
  1. Disconnect the vacuum switching valve assembly connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E45-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vacuum Switching Valve Assembly (for ACIS))



NG
Go to step 7
OK


6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY - ECM)
  1. Disconnect the vacuum switching valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E45-1 (ACIS) - E26-69 (ACIS)
    Always
    Below 1 Ω
    E45-1 (ACIS) or E26-69 (ACIS) - Body ground
    Always
    10 kΩor higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - VACUUM SWITCHING VALVE ASSEMBLY)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the vacuum switching valve assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-8 - E45-2 (+B)
    Always
    Below 1 Ω
    1A-8 or E45-2 (+B) - Body ground
    Always
    10 kΩor higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)