Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2808    Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4)

for Preparation Click here


DESCRIPTION

The TCM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems of the shift solenoid valves and valve body.

DTC No.
DTC Detection Condition
Trouble Area
P2808
The engine revs freely when 3rd or 5th gear is commanded. (2-trip detection logic)
When any of the following is detected. In addition, the condition that 4th gear is engaged when 4th gear is commanded occurs twice. (2-trip detection logic)
  1. When 1st gear is commanded, 3rd gear is engaged.
  2. When 2nd gear is commanded, 3rd gear is engaged.
  3. When 6th gear is commanded, 5th gear is engaged.
  1. Shift solenoid valve SL4 remains open or closed
  2. Valve body is blocked
  3. Automatic transaxle (clutch, brake or gear etc.)

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2808:
Shift solenoid valve SL4/OFF malfunction
Shift solenoid valve SL4/ON malfunction
Required sensors/Components
Shift solenoid valve SL4, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE)
Frequency of operation
Continuous
Duration
OFF malfunction (A): 0.5 sec.
OFF malfunction (B): 0.8 sec.
ON malfunction: 0.8 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL: 
The monitor will run whenever this DTC is not present.
(Not circuit malfunction)
P0712, P0713 (ATF temperature sensor circuit (TFT sensor))
P0115, P0117, P0118 (ECT sensor circuit)
P0715, P0717 (Turbine speed sensor circuit)
P0791, P0793 (Intermediate shaft speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P2810 (Shift solenoid valve SL4 circuit)
P0327, P0328, P0332, P0333 (KCS sensor circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system)
U0100 (CAN communication system)
Transmission range
"D"
TFT (Transmission fluid temperature)
-10°C (14°F) or more
TFT (Transmission fluid temperature) sensor circuit
No circuit malfunction
ECT (Engine coolant temperature) sensor circuit
No circuit malfunction
Turbine speed sensor circuit
No circuit malfunction
Intermediate shaft speed sensor circuit
No circuit malfunction
Shift solenoid valve SL1 circuit
No circuit malfunction
Shift solenoid valve SL2 circuit
No circuit malfunction
Shift solenoid valve SL3 circuit
No circuit malfunction
Shift solenoid valve SL4 circuit
No circuit malfunction
(KCS) Knock control sensor circuit
No circuit malfunction
(ETCS) Electronic throttle control system
Not system down
CAN communication system
Not system down
Engine
Starting

OFF malfunction (A): 
TCM select gear
3rd or 5th
Throttle valve opening angle
3% or more

OFF malfunction (B): 
TCM select gear
3rd
Throttle valve opening angle
4.5% or more
Vehicle speed
1.2 mph (2 km/h) or more
ECT (Engine coolant temperature)
40°C (104°F) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

ON malfunction (A): 
TCM select gear
1st
Time after transmission to 1st gear
0.1 sec. or more
Vehicle speed
1.2 mph (2 km/h) to 24.9 mph (40 km/h)
ECT (Engine coolant temperature)
40°C (104°F) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

ON malfunction (B): 
TCM select gear
2nd
Throttle valve opening angle
4.5% or more at engine speed 2,000 rpm (condition varies with engine speed)
Vehicle speed
1.2 mph (2 km/h) or more
ECT (Engine coolant temperature)
40°C (104°F) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

ON malfunction (C): 
TCM select gear
6th
Throttle valve opening angle
4.5% or more at engine speed 2,000 rpm (condition varies with engine speed)
Vehicle speed
1.2 mph (2 km/h) or more
ECT (Engine coolant temperature)
40°C (104°F) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

ON malfunction (D): 
TCM select gear
4th
Throttle valve opening angle
4.5% or more at engine speed 2,000 rpm (condition vary with engine speed)
Vehicle speed
1.2 mph (2 km/h) or more
ECT (Engine coolant temperature)
40°C (104°F) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

TYPICAL MALFUNCTION THRESHOLDS


OFF malfunction (A): 
Turbine speed - Output speed x Gear ratio
1,000 rpm or more

OFF malfunction (B): 
Turbine speed / Output speed
3.304 to 7.724

ON malfunction (A) and (B): 
Turbine speed / Output speed
1.399 to 1.649

ON malfunction (C): 
Turbine speed / Output speed
0.705 to 0.836

ON malfunction (D): 
Turbine speed / Output speed
0.998 to 1.138

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2808)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.

    Result:

    Display (DTC output)
    Proceed to
    Only "P2808" is output
    A
    "P2808" and other DTCs are output
    B

HINT:
If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.



A
Go to step 3
B


2.PERFORM ACTIVE TEST USING TECHSTREAM

NOTICE:
This test should always be performed with at least 2 people.

  1. Warm up the engine.

  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    HINT:
    Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).

    Tester Display
    Test Details
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to selected manually.
    1. Press "→" button: Upshift occurs
    2. Press "←" button: Downshift occurs
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    50 km/h (31 mph) or less

    NOTICE:
    1. This test can be conducted when the vehicle is stopped.
    2. When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.

    HINT:
    The gear commanded by the TCM is shown in the Data List / Shift Status display on the Techstream.

  1. Check the vehicle speed and the gear when the engine speed is 1000 rpm.

    HINT:
    Because the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


    Standard:

    1st
    2nd
    3rd
    4th
    5th
    6th
    8 to 12 km/h (5 to 7.5 mph)
    15 to 19 km/h (9.3 to 11.8 mph)
    21 to 25 km/h (13.0 to 15.5 mph)
    31 to 35 km/h (19.3 to 21.7 mph)
    44 to 48 km/h (27.3 to 29.8 mph)
    52 to 56 km/h (32.3 to 34.8 mph)

  1. Compare the TCM commanded gear and the actual gear.

    Result:

    Actuator Gear during Malfunction
    TCM Commanded Gear
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid SL1
    Stuck ON
    1st
    2nd
    3rd
    4th
    4th
    4th
    A
    Stuck OFF
    N*1
    N*1
    N*1
    N*1
    5th
    6th
    Shift solenoid SL2
    Stuck ON
    4th
    4th
    4th
    4th
    5th
    6th
    B
    Stuck OFF
    1st
    2nd
    3rd
    1st
    N*1
    N*1
    Shift solenoid SL3
    Stuck ON
    2nd
    2nd
    3rd
    4th
    5th
    6th
    C
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*1
    Shift solenoid SL4
    Stuck ON*3
    3rd
    3rd
    3rd
    4th
    5th
    5th
    D
    Stuck OFF
    1st
    2nd
    1st
    4th
    N*1
    6th
    Shift solenoid SLT
    Stuck ON
    N*2
    N*2
    N*2
    N*2
    N*2
    N*2
    E
    Stuck OFF*3
    1st
    2nd
    3rd
    4th
    5th
    6th

    HINT:
    1. *1: Neutral
    2. *2: If shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
    3. *3: When shift solenoid SLT is stuck off, gear shifting is normal.



A
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL1) PERFORMANCE DTC P0746) (Click here)

B
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL2) PERFORMANCE DTC P0776) (Click here)

C
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL3) PERFORMANCE DTC P0796) (Click here)

E
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SLT) PERFORMANCE DTC P2714) (Click here)
D


3.INSPECT SHIFT SOLENOID VALVE SL4


    C201747E01
  1. Remove shift solenoid valve SL4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Shift Solenoid Valve SL4

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL4 (Click here)
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

OK:
There are no foreign objects on each valve and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)