Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2GR-FE)

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

for Preparation Click here


DESCRIPTION

The torque sensor converts the steering wheel rotation torque into electric signals and sends them to the power steering ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
C1511
Torque sensor malfunction
  1. Electric power steering column sub-assembly (Torque sensor)
  2. Power steering ECU assembly
C1512
C1513
C1514

WIRING DIAGRAM


C240198E01


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
  1. Check the connection condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
C238944E01
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b-3 (TRQV) - b-1 (TRQG)
    Engine switch on (IG)
    8.5 to 10.5 V
    b-5 (TRQF) - b-1 (TRQG)
    Engine switch on (IG)
    3.35 to 3.37 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C238944E02
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition (Steering Wheel Position)
    Specified Condition
    b-7 (TRQ1) - b-1 (TRQG)
    Engine running
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Engine running
    Steering wheel being turned to the right with vehicle stopped
    2.5 to 4.7 V
    Engine running
    Steering wheel being turned to the left with vehicle stopped
    0.3 to 2.5 V
    b-2 (TRQ2) - b-1 (TRQG)
    Engine running
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Engine running
    Steering wheel being turned to the right with vehicle stopped
    0.3 to 2.5 V
    Engine running
    Steering wheel being turned to the left with vehicle stopped
    2.5 to 4.7 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Inspection Item
    Condition (Steering Wheel Position)
    Specified Condition
    Sum of voltage between b-7 (TRQ1) and b-1 (TRQG) and voltage between b-2 (TRQ2) and b-1 (TRQG)
    Engine running
    Steering wheel not being turned (without load)
    Between 4.85 V and 5.35 V
    Engine running
    Steering wheel being turned to the right with vehicle stopped
    Engine running
    Steering wheel being turned to the left with vehicle stopped



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)