Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2AR-FE without Wireless Door Lock)

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

DTC    C1517    Torque Hold Abnormal

for Preparation Click here


DESCRIPTION

The torque sensor converts the rotation torque received from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
C1511
Torque sensor malfunction
  1. Electric power steering column sub-assembly (Torque sensor)
  2. Power steering ECU assembly
C1512
C1513
C1514
C1517

WIRING DIAGRAM


C245322E05


INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (Click here).
  2. If the electric power steering column sub-assembly has been replaced with a new one, perform torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Check the connection condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
C238943E03
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z16-8 (TRQV) - Body ground
    Engine running
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C238943E04
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    (Steering Wheel Position)
    Specified Condition
    z16-9 (TRQ1) - Body ground
    Engine running
    (Center position)
    2.3 to 2.7 V
    z16-1 (TRQ2) - Body ground
    Engine running
    (Center position)
    2.3 to 2.7 V
    z16-9 (TRQ1) - Body ground
    Engine running
    (Turned to right)
    2.5 to 3.8 V
    z16-1 (TRQ2) - Body ground
    Engine running
    (Turned to right)
    1.2 to 2.5 V
    z16-9 (TRQ1) - Body ground
    Engine running
    (Turned to left)
    1.2 to 2.5 V
    z16-1 (TRQ2) - Body ground
    Engine running
    (Turned to left)
    2.5 to 3.8 V

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Inspection Item
    Condition (Steering Wheel Position)
    Specified Condition
    Sum of voltage between z16-9 (TRQ1) and body ground and voltage between z16-1 (TRQ2) and body ground
    Engine running
    Steering wheel not being turned (without load)
    Between 4.75 V and 5.25 V
    Engine running
    Steering wheel being turned to the right with vehicle stopped
    Engine running
    Steering wheel being turned to the left with vehicle stopped

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)