Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Ignition Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) determines the ignition position (LOCK, ACC, ON) based on signals from the IG or ACC circuit.

WIRING DIAGRAM


B289671E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch/ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch LOCK
    -
    IG SW
    Ignition switch/ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch LOCK or ACC
    -

    OK:
    ON or OFF appears on the screen according to whether the ignition switch is in ON or is in LOCK or ACC.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY


    B289672E01
  1. Remove the ignition or starter switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 4
    Ignition switch ON
    Below 1 Ω
    2 - 4
    Ignition switch ACC
    Below 1 Ω

    Text in Illustration 
    *1
    LOCK
    *2
    ACC
    *3
    ON
    *4
    START
    *a
    Component without harness connected
    (Ignition or Starter Switch Assembly)



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3E instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3E-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-7 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3A instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I36-1 (IG1) - 3A-27
    Always
    Below 1 Ω
    I36-1 (IG1) - Body ground
    Always
    10 kΩ or higher
    I36-2 (ACC) - 3B-23
    Always
    Below 1 Ω
    I36-2 (ACC) - Body ground
    Always
    10 kΩ or higher
    I36-4 (AM1) - 3A-39
    Always
    Below 1 Ω
    I36-4 (AM1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)