ENGINE ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM |
Turn the A/C switch on.
Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.
Turn the ignition switch off.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. DISCHARGE FUEL SYSTEM PRESSURE |
| 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 6. REMOVE FRONT WHEELS |
| 7. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 8. REMOVE ENGINE UNDER COVER RH |
| 9. REMOVE FRONT FENDER APRON SEAL RH |
| 10. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 11. REMOVE ENGINE UNDER COVER LH |
| 12. REMOVE FRONT FENDER APRON SEAL LH |
| 13. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil drain plug and drain the oil into a container.
Clean the oil drain plug.
Install the oil drain plug with a new gasket.
| 14. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Loosen the 2 cylinder block drain cock plugs.
Remove the radiator cap sub-assembly.

| *1 | Radiator Cap Sub-assembly | *2 | Cylinder Block Drain Cock Plug |
| *3 | Radiator Drain Cock Plug | *4 | Air Drain Cock Plug |
| 15. DRAIN AUTOMATIC TRANSAXLE FLUID |
Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.
![]() |
Remove the refill plug and gasket from the automatic transaxle.
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle.
![]() |
Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
Drain automatic transaxle fluid from the automatic transaxle.
![]() |
Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
![]() |
Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle.
![]() |
Temporarily install the gasket and refill plug to the automatic transaxle.
| 16. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 7 clips and cool air intake duct seal.
| 17. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 retainers on the front of the V-bank cover sub-assembly. Continue to raise the V-bank cover sub-assembly to disengage the retainer on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.
| 18. REMOVE INLET NO. 2 AIR CLEANER |
![]() |
Disconnect the 2 wire harness clamps and vacuum hose clamp.
Remove the 2 bolts and inlet No. 2 air cleaner.
| 19. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp.
![]() |
Disconnect the 3 hoses.
Separate the ventilation hose.
![]() |
Loosen the hose clamp and separate the air cleaner cap sub-assembly from the throttle with motor body assembly.
Release the 2 clamps and remove the air cleaner cap with hose.
| 20. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 21. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Disconnect the wire harness clamp, connector, vacuum hose and No. 1 fuel vapor feed hose.
Remove the 2 bolts and air cleaner case sub-assembly.
| 22. REMOVE BATTERY |
![]() |
Disconnect the positive (+) cable from the positive (+) battery terminal.
Loosen the nut and remove the bolt.
Remove the battery and battery tray.
| 23. REMOVE INLET NO. 1 AIR CLEANER |
![]() |
Disengage the pin and remove the inlet No. 1 air cleaner.
| 24. REMOVE INTAKE AIR RESONATOR SUB-ASSEMBLY |
![]() |
Disengage the claw and disconnect the 2 vacuum hoses.
Remove the 2 bolts and intake air resonator sub-assembly.
| 25. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.
| 26. REMOVE ENGINE MOVING CONTROL ROD BRACKET |
![]() |
Remove the 4 bolts and engine moving control rod bracket with engine moving control rod.
| 27. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the bolt and engine moving control rod from the engine moving control rod bracket.
| 28. SEPARATE EARTH WIRE |
![]() |
Remove the 2 bolts and separate the earth wire from the engine assembly.
| 29. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE |
![]() |
Disconnect the No. 1 fuel vapor feed hose.
| 30. DISCONNECT UNION TO CHECK VALVE HOSE |
![]() |
Disconnect the union to check valve hose from the brake booster.
| 31. DISCONNECT INLET RADIATOR HOSE |
![]() |
Remove the hose clamp to separate the air fuel ratio sensor wire from the inlet radiator hose.
Remove the hose clamp to separate the No. 3 water by-pass hose from the inlet radiator hose.
Disconnect the inlet radiator hose.
| 32. DISCONNECT OUTLET RADIATOR HOSE |
![]() |
Disconnect the outlet radiator hose.
| 33. DISCONNECT NO. 3 WATER BY-PASS HOSE |
![]() |
Disconnect the No. 3 water by-pass hose from the transmission oil cooler.
| 34. DISCONNECT INLET HEATER WATER HOSE |
![]() |
Disconnect the inlet heater water hose.
| 35. DISCONNECT WATER HOSE SUB-ASSEMBLY |
![]() |
Disconnect the water hose sub-assembly.
| 36. REMOVE STARTER ASSEMBLY |
![]() |
Disconnect the starter connector.
Remove the terminal cap.
Remove the nut and disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 37. DISCONNECT ENGINE WIRE |
Remove the No. 1 relay block cover.
![]() |
Remove the 2 nuts and disconnect the wire clamp.
Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.
![]() |
Disconnect the 4 connectors.
Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.
![]() |
Pull up the lever to disconnect the ECM connector.
Disconnect the 2 wire clamps.
| 38. REMOVE AIR CLEANER BRACKET |
![]() |
Disconnect the 2 wire clamps.
Remove the bolt and No. 1 air cleaner bracket from the battery carrier.
| 39. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY |
Move the shift lever to N.
![]() |
Disconnect the wire harness clamp.
![]() |
Remove the nut from the control shaft lever.
Remove the clip and disconnect the transmission control cable from the control cable bracket.
| 40. DISCONNECT FUEL MAIN TUBE |
![]() |
Remove the No. 1 fuel pipe clamp.
![]() |
Disconnect the connector from the pipe by hand. When the connector and the pipe are stuck, push in and pull on the connector to release it. Pull the connector out of the pipe carefully.
![]() | Push |
![]() | Pull |
| 41. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Disconnect the 3 connectors.
Disengage the 2 clamps.
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor and magnetic clutch.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
| 42. DISCONNECT SUCTION HOSE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.
Remove the O-ring from the suction hose sub-assembly.
| 43. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET |
![]() |
Remove the 2 nuts and No. 1 exhaust pipe support bracket (for Front Side).
| 44. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Disconnect the 2 wire harnesses from the clamp.
Disconnect the 2 heated oxygen sensor connectors.
![]() |
Remove the 2 bolts and No. 1 exhaust pipe support bracket (for Rear Side).
![]() |
Remove the 4 bolts, 4 nuts and front exhaust pipe assembly.
Remove the 3 gaskets from the front exhaust pipe assembly.
| 45. SECURE STEERING WHEEL |
![]() |
Secure the steering wheel with the seat belt in order to prevent rotation.
| 46. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the steering intermediate shaft assembly and steering link assembly.
| *a | Matchmark |
Remove the bolt.
Separate the steering intermediate shaft assembly from the steering link assembly.
| 47. REMOVE FRONT AXLE SHAFT NUT LH |
![]() |
Using SST and a hammer, release the staked part of the front axle shaft nut.
While applying the brakes, remove the front axle shaft nut.
| 48. REMOVE FRONT AXLE SHAFT NUT RH |
| 49. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.
| 50. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 51. SEPARATE FRONT SPEED SENSOR LH |
![]() |
Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.
![]() |
Remove the bolt and front speed sensor from the steering knuckle.
| 52. SEPARATE FRONT SPEED SENSOR RH |
| 53. SEPARATE TIE ROD ASSEMBLY LH |
![]() |
Remove the cotter pin and nut.
![]() |
Install SST to the tie rod assembly LH.
Secure SST using a string.
Using SST, separate the tie rod assembly LH from the steering knuckle.

| *1 | Center Nut | - | - |
| *a | String | *b | Grease Application Area |
![]() | Place the wrench here. | - | - |
| 54. SEPARATE TIE ROD ASSEMBLY RH |
| 55. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.
| 56. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 57. SEPARATE FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
| *a | Matchmark |
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.
| 58. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the front drive shaft assembly LH.
| 59. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH |
![]() |
Using a screwdriver, remove the front drive shaft hole snap ring LH.
| 60. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.
| 61. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET |
![]() |
Remove the bolt and No. 1 exhaust pipe support bracket.
| 62. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and No. 1 exhaust pipe support bracket sub-assembly.
| 63. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
![]() |
Turn the crankshaft to gain access to the removable locations of the 6 torque converter setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.
| 64. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
![]() |
Set the engine lifter.
![]() | Attachment Installation Position |
![]() |
Remove the 4 bolts, 2 nuts and frame side rail plates RH and LH.
Remove the 4 bolts, 2 nuts and front suspension member rear braces RH and LH.
Operate the engine lifter, then remove the engine assembly from the vehicle.
Install the engine hangers .
| 65. REMOVE V-RIBBED BELT |
![]() |
Release the V-ribbed belt tension by turning the V-ribbed belt tensioner counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner.
While turning the V-ribbed belt tensioner counterclockwise, align its holes, and then insert a 5 mm hexagon wrench into the holes to fix the V-ribbed belt tensioner.
| 66. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Disconnect the generator connector from the generator assembly.
Remove the bolt and disconnect the wire harness clamp.
![]() |
Remove the 2 bolts.
![]() |
Remove the 2 bolts and generator assembly.
Disconnect the wire harness clamp and remove the generator bracket.
| 67. REMOVE COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Remove the 4 bolts and compressor and magnetic clutch and bracket.
| 68. REMOVE TRANSMISSION OIL COOLER |
![]() |
Disconnect the breather plug and remove the clamp.
Remove the No. 4 water by-pass hose.
![]() |
Remove the No. 1 oil cooler outlet hose and No. 1 oil cooler inlet hose.
| *1 | No. 1 Oil Cooler Outlet Hose |
| *2 | No. 1 Oil Cooler Inlet Hose |
![]() |
Remove the 2 bolts and transmission oil cooler with the transmission oil cooler stay from the automatic transaxle assembly.
| 69. REMOVE FRONT FRAME ASSEMBLY |
![]() |
Disconnect the oil pressure switch connector and 2 clamps.
![]() |
Disconnect the 2 clamps and vacuum switching valve connector.
Remove the bolt and disconnect the front engine mounting insulator.
![]() |
Remove the nut and disconnect the engine mounting insulator LH.
![]() |
Remove the nut and disconnect the engine mounting insulator RH.
Remove the front frame assembly.
| 70. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY |
![]() |
Remove the 3 nuts and front engine mounting insulator assembly.
| 71. REMOVE ENGINE MOUNTING INSULATOR LH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator LH.
| 72. REMOVE ENGINE MOUNTING INSULATOR RH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator RH.
| 73. REMOVE ENGINE WIRE |
Remove the engine wire from the engine with transaxle.
| 74. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY |
Using the transmission jack attachment, set the automatic transaxle assembly on a transmission jack.
![]() |
Remove the 11 bolts and transaxle.
| 75. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 3 bolts and engine mounting bracket RH.
| 76. REMOVE DRIVE SHAFT BEARING BRACKET |
![]() |
Remove the 3 bolts and drive shaft bearing bracket.
| 77. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts, front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer.
| 78. INSTALL ENGINE ON ENGINE STAND |
Install the engine onto an engine stand with the bolts.