Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor assembly LH (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly LH (for driver door) has motor, regulator and ECU functions.
This DTC is stored when the ECU built into the regulator motor determines that the power window regulator master switch assembly is stuck.

D-Door Motor (Power Window Regulator Motor Assembly LH (for Driver Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator master switch assembly (for driver door) stuck
  2. Power window regulator master switch assembly held in same position for more than 20 seconds
  1. Power window regulator master switch assembly
  2. Power window regulator motor assembly LH (for driver door)
  3. Wire harness or connector

WIRING DIAGRAM


B281016E09


INSPECTION PROCEDURE

NOTICE:
  1. DTC B2312 can be stored in the power window regulator motor assembly LH (for driver door).
  2. If a power window regulator motor assembly LH (for driver door) has been replaced with a new one, initialize the power window control system (Click here).
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2312 is not output.



NG
Go to step 2
OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE) 

2.READ VALUE USING TECHSTREAM (DRIVER DOOR WINDOW MOTOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / D-Door Motor / Data List.

  1. Read the Data List according to the display on the Techstream.

    D-Door Motor (Power Window Regulator Motor Assembly LH (for Driver Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / ON or OFF
    ON: Driver door power window auto switch operated
    OFF: Driver door power window auto switch not operated
    -
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -

    OK:
    On the Techstream screen, ON or OFF is displayed accordingly.



NG
Go to step 3
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)  

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR LH (FOR DRIVER DOOR))
  1. Disconnect the power window regulator master switch assembly connector.

  1. Disconnect the power window regulator motor assembly LH (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-8 (U) - Body ground
    Always
    10 kΩ or higher
    K11-5 (D) - Body ground
    Always
    10 kΩ or higher
    K11-4 (A) - Body ground
    Always
    10 kΩ or higher
    K9-10 (UP1) - Body ground
    Always
    10 kΩ or higher
    K9-7 (DWN1) - Body ground
    Always
    10 kΩ or higher
    K9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B164359E71
  1. Remove the power window regulator master switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (U) - 1 (E)
    Released
    10 kΩ or higher
    8 (U) - 4 (A)
    Released
    10 kΩ or higher
    4 (A) - 1 (E)
    Released
    10 kΩ or higher
    5 (D) - 1 (E)
    Released
    10 kΩ or higher
    4 (A) - 5 (D)
    Released
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR DRIVER DOOR) (Click here)