Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Intuitive Parking Assist System)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Intuitive Parking Assist System) > Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

for Preparation Click here


DESCRIPTION

Vehicle speed signal is received from the combination meter assembly.
The signal is used for DVD viewing restriction while driving, etc.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.


WIRING DIAGRAM


for 2AR-FE

E224311E01


for 2GR-FE

E224310E01


INSPECTION PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)


    E227878
  1. Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check (Click here).

  1. While driving the vehicle, compare the "SPEED" indicator to the reading on the speedometer. Check if these readings are almost equal.

    HINT:
    The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

    OK:
    Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the Techstream (Click here).



NG
Go to step 2
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)


    E204779E06
  1. Check the output waveform.

    1. Remove the combination meter assembly with the connector still connected.

    2. Connect an oscilloscope to terminal I18-9 (+S) and body ground.

    3. Turn the ignition switch to ON.

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Measurement terminal
      I18-9 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD) - I18-9 (+S)
    Always
    Below 1 Ω



NG
Go to step 4
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the navigation ECU sub-assembly connector.

  1. Disconnect the junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD) - I124-17
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)