ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT BATTERY |
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.
Install the air cleaner filter element sub-assembly.
| 5. INSPECT SPARK PLUG |
| 6. INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE |
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.
If any defects or problems are found during the inspection above, perform a lash adjuster inspection .
| 7. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Start the engine and idle it.
Turn the Techstream main switch on.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.
When not using the Techstream:
Remove the No. 1 engine cover sub-assembly.
![]() |
Pull out the wire harness as shown in the illustration.
Connect the clip of a timing light to the wire harness.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Using a timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Disconnect the timing light from the engine.
Install the No. 1 engine cover sub-assembly.
| 8. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the Techstream main switch on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Disconnect the Techstream from the DLC3.
When not using the Techstream:
![]() |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
| *1 | DLC3 |
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer probe from the DLC3.
| 9. INSPECT COMPRESSION |
Warm up and stop the engine.
Check for DTCs (Click here).
Remove the 4 spark plugs .
Disconnect the 4 fuel injector connectors.
![]() |
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs .
Clear the DTCs (Click here).
| 10. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|