Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM

DTC    C1622    Open or Short Circuit in Back Camera Signal

for Preparation Click here


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly judges that the signals or signal lines between the navigation ECU sub-assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No.
DTC Detection Condition
Trouble Area
C1622
Open or short in the rear television camera assembly signal circuit
  1. Harness or connector
  2. Rear television camera assembly
  3. Navigation ECU sub-assembly

WIRING DIAGRAM


E226207E01


INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the I66 connector from the navigation ECU sub-assembly.

  1. Disconnect the T6 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I66-7 (CA+) - T6-6 (CB+)
    Always
    Below 1 Ω
    I66-8 (V+) - T6-3 (CV+)
    Always
    Below 1 Ω
    I66-15 (CGND) - T6-5 (CGND)
    Always
    Below 1 Ω
    I66-16 (V-) - T6-2 (CV-)
    Always
    Below 1 Ω
    I66-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    I66-8 (V+) - Body ground
    Always
    10 kΩ or higher
    I66-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    I66-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION ECU SUB-ASSEMBLY (V-, CGND, CA+)


    E216447E03
  1. Reconnect the I66 connector to the navigation ECU sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I66-15 (CGND) - Body ground
    Always
    Below 1 Ω
    I66-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I66-7 (CA+) - I66-15 (CGND)
    Engine switch on (IG)
    Shift lever in R
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU sub-assembly)



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK


3.CHECK NAVIGATION ECU SUB-ASSEMBLY (V+, GND1)
  1. Reconnect the T6 connector to the rear television camera assembly.



    E224383E01
  1. Reconnect the I66 connector to the navigation ECU sub-assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Navigation ECU sub-assembly)
    *b
    Waveform 1 (camera lens is not covered, displaying an image)
    *c
    Waveform 2 (camera lens is covered, blacking out the screen)
    *d
    Synchronization Signal
    *e
    Video Waveform

  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    I66-8 (V+) - I66-7 (GND1)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Engine switch on (IG), shift lever in R

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)