DTC B27A2 Open in Front Passenger Side Electrical Antenna Circuit |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B27A2 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly RH (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (1 trip detection logic*). |
| Any time |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Entry lock/unlock operation cannot be performed for front passenger door | - |
| DTC Code | Data List and Active Test |
| B27A2 | Key diagnostic mode can be used to perform troubleshooting |

| 1.CHECK CONNECTOR CONNECTION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly RH (for front passenger door).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH) |
Disconnect the A43 and I78 certification ECU (smart key ECU assembly) connectors.
Disconnect the V1 front door outside handle assembly RH (for front passenger door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-11 (CLG2) - V1-6 (ANT1) | Always | Below 1 Ω |
| I78-10 (CG2B) - V1-3 (ANT2) | Always | Below 1 Ω |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| V1-2 (GND) - Body ground | Always | Below 1 Ω |
| I78-11 (CLG2) or V1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| I78-10 (CG2B) or V1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER SIDE ELECTRICAL KEY ANTENNA) |
Connect the A43 and I78 certification ECU (smart key ECU assembly) connectors.

| *1 | Waveform 1 | *2 | Waveform 2 |
| *a | Component with harness connected (Certification ECU (smart key ECU assembly)) | - | - |
Connect the V1 front door outside handle assembly RH (for front passenger door) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| I78-11 (CLG2) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| I78-11 (CLG2) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
| I78-10 (CG2B) - A43-11 (E) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
|
| ||||
| OK | |
| 4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH (FOR FRONT PASSENGER DOOR) |
Temporarily replace the front door outside handle assembly RH (for front passenger door) with a new or known good one (Click here).
| NEXT | |
| 5.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 6.CHECK FOR DTC |
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||