INSTRUMENT PANEL SAFETY PAD > INSTALLATION |
| 1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.

Install the 2 clips.
Install the 3 bolts <B> and nut <F> or <G>.
Install the 2 passenger airbag bolts <A>.
Engage each clamp.
Connect each connector.
| 2. CONNECT NO. 2 INSTRUMENT PANEL WIRE |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the connector.
| 3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY |
![]() |
Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly.
| 4. INSTALL CONSOLE BOX INSERT |
![]() |
Engage the clip and 3 guides.
Install the console box insert with the 2 screws <C> or <D>.
| 5. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the clip and 3 guides.
Install the front No. 2 console box insert with the 2 screws <C> or <D>.
Engage the 2 claws to connect the room temperature sensor.
| 6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
w/ Smart Key System:
Connect the connector.
Engage the 4 clips to install the lower instrument panel finish panel assembly.
| 7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
Connect the connector.
![]() |
Install the front No. 2 speaker assembly with the 2 screws.
| *A | LH Side |
| *B | RH Side |
| 8. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.
| 9. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
![]() |
Install the front pillar garnish clip to front pillar garnish LH.
Engage the 2 guides as shown in the illustration.
![]() |
Engage the 2 clips to install the front pillar garnish LH.
| 10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 11. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.
| 12. INSTALL FRONT PILLAR GARNISH RH |
| 13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips to install the No. 3 instrument panel register assembly.
| 14. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 5 clips to install the No. 2 instrument cluster finish panel garnish.
| 15. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the glove compartment light as shown in the illustration.
![]() |
Engage the guide and 2 clips.
Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.
| 16. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.
| *1 | Airbag Connector |
| *2 | Airbag Connector Lock |
Push in the lock to install the airbag connector.
Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.
Install the 3 bolts.
| 17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
| 18. INSTALL INSTRUMENT SIDE PANEL RH |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
| 19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 21. INSTALL FRONT DOOR SCUFF PLATE RH |
| 22. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers) |
Connect the connector.
![]() |
Install the front No. 3 speaker assembly with the 2 screws.
| 23. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY |
Connect the connector.
![]() |
Engage the 8 clips to install the No. 1 speaker opening cover assembly.
| 24. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type) |
Connect each connector.
Engage the 8 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.
Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.
| 25. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type) |
Connect each connector.
Engage the 8 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.
Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.
| 26. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type) |
Connect each connector.
Engage the 8 clips to the vehicle body to temporarily install the navigation receiver assembly with air conditioning control assembly.
Install the navigation receiver assembly with air conditioning control assembly with the 4 bolts.
| 27. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect each connector.
Engage the 4 clips and guide.
Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
| 28. INSTALL BOX BOTTOM MAT |
Install the box bottom mat.
| 29. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 6 clips to install the No. 2 instrument panel register assembly.
| 30. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
Connect the connector.
Engage the clamp.
![]() |
Engage the 6 clips and 7 claws to install the center instrument cluster finish panel assembly.
| 31. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() |
Engage the 4 guides as shown in the illustration.
Install the rear console box assembly with the 2 bolts and 2 screws.
| 32. INSTALL CONSOLE BOX CARPET |
Install the console box carpet.
| 33. INSTALL NO. 4 CONSOLE BOX DUCT (w/ Rear Register Duct) |
Engage the claw to install the No. 4 console box duct.
| 34. INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY |
w/ Power Outlet Socket:
Connect the connector.
Engage the clamp.
![]() |
Engage the 4 clips as shown in the illustration.
Install the upper console box sub-assembly with the 2 screws.
| 35. INSTALL CONSOLE BOX CUP HOLDER |
Install the console box cup holder to the instrument panel cup holder tray.
| 36. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY |
Install the front console upper panel garnish.
Install the instrument panel cup holder tray and front console upper panel garnish with the 6 screws <C> or <D>.
| 37. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY |
Connect the connector.
w/ Seat Heater System:
Connect the 2 connectors.
Engage the 4 clips and install the rear console upper panel sub-assembly.
Move the shift lever to P.
| 38. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.
| 39. INSTALL FRONT PANEL GARNISH RH |
Engage the 3 claws, 2 clips and 8 guides to install the front panel garnish RH.
| 40. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Engage the 4 claws, 9 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.
| 41. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
| 42. INSTALL FRONT PANEL GARNISH LH |
Engage the 3 claws, 2 clips and 8 guides to install the front panel garnish LH.
| 43. INSTALL COMBINATION METER ASSEMBLY |
Connect the 2 connectors.
Engage the wire harness clamp.
Install the combination meter assembly with the 4 screws.
| 44. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Temporarily install the instrument cluster finish panel assembly as shown in the illustration.
Connect each connector.
Engage the 5 claws, 5 clips and 2 guides, and install the instrument cluster finish panel assembly.
![]() |
Engage the 2 claws, 4 clips and 2 guides.
| 45. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Engage the 4 clips to install the No. 1 instrument panel register assembly.
| 46. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 3 clips to install the No. 1 instrument cluster finish panel garnish.
| 47. INSTALL INSTRUMENT SIDE PANEL LH |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
| 48. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 49. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
| 50. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 10 claws to install the front door scuff plate LH.
| 51. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 52. INSPECT SRS WARNING LIGHT |