Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM

PARKING ASSIST MONITOR SYSTEM > Guide Lines and Buttons are not Displayed for All Display Modes

for Preparation Click here


DESCRIPTION

The navigation ECU sub-assembly receives luggage compartment door lock assembly open/close signals from the main body ECU (multiplex network body ECU) via CAN communication. When the luggage compartment door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the luggage compartment door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.

HINT:
  1. Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)
  2. The luggage compartment door lock assembly is connected to the main body ECU (multiplex network body ECU) by the vehicle wire harness.


WIRING DIAGRAM


E224384E01


INSPECTION PROCEDURE

NOTICE:
  1. When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Luggage Courtesy SW
    Luggage compartment door courtesy switch signal/ON or OFF
    ON: Luggage compartment door open
    OFF: Luggage compartment door closed
    -

    OK:
    The luggage compartment door courtesy switch functions as specified in the normal condition column.



NG
Go to step 2
OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)  

2.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    B281816E02
  1. Check operation of the door courtesy switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Measurement Condition
      Switch Condition
      Specified Condition
      2 (E) - 3 (D+)
      Close (Lock)
      10 kΩ or higher
      2 (E) - 3 (D+)
      Open (Unlock)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Luggage Compartment Door Lock Assembly)
      *b
      Close (Lock)
      *c
      Open (Unlock)



NG
REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the T3 luggage compartment door lock assembly connector.

  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T3-3 (D+) - 3C-9
    Always
    Below 1 Ω
    T3-3 (D+) - Body ground
    Always
    10 kΩ or higher
    T3-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173023E09


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-9 - MB-4 (LGCY)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)