Home › Audio/Visual/Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15CC    Backup Battery Failure

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects one of the following:
  1. Open or short in the BUB (Back-Up Battery) circuit.
  2. The BUB (Back-Up Battery) voltage drops or the BUB (Back-Up Battery) malfunctions.
  3. The BUB (Back-Up Battery) temperature is (temporarily) high.

DTC No.
DTC Detection Condition
Trouble Area
B15CC
BUB (Back-Up Battery) malfunction
  1. Wire harness or connector
  2. BUB (Back-Up Battery)
  3. DCM (Telematics Transceiver)

WIRING DIAGRAM


B278896E03


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "Health Check" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B15CC is output
    A
    DTC B15CC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BUB (BACK-UP BATTERY))
  1. Disconnect the I135 DCM (Telematics Transceiver) connector.

  1. Disconnect the I136 BUB (Back-Up Battery) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-30 (BBI+) - I136-1 (BBO+)
    Always
    Below 1 Ω
    I135-13 (BBI-) - I136-5 (BBO-)
    Always
    Below 1 Ω
    I135-20 (CTR1) - I136-3 (BTR1)
    Always
    Below 1 Ω
    I135-21 (CTR2) - I136-4 (BTR2)
    Always
    Below 1 Ω
    I135-30 (BBI+) - Body ground
    Always
    10 kΩ or higher
    I135-13 (BBI-) - Body ground
    Always
    10 kΩ or higher
    I135-20 (CTR1) - Body ground
    Always
    10 kΩ or higher
    I135-21 (CTR2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE BUB (BACK-UP BATTERY)
  1. Replace the BUB (Back-Up Battery) with a known good one and check if the same problem occurs again (Click here).

    NOTICE:
    The BUB (Back-Up Battery) must not be replaced while an ACN call is in progress.


NEXT


4.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5.RECHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTC is output.



NG
Go to step 6
OK

END 

6.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The engine switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)