Home › Audio/Visual/Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C4    Airbag Signal Malfunction/Not Input

for Preparation Click here


DESCRIPTION

If the DCM (Telematics Transceiver) detects an error in communication between the DCM (Telematics Transceiver) and the airbag sensor assembly as a result of the DCM (Telematics Transceiver) self check, this DTC will be set.

DTC No.
DTC Detection Condition
Trouble Area
B15C4
DCM (Telematics Transceiver) detects an error in signals from airbag sensor assembly when engine switch is on (IG).
  1. Airbag system
  2. Wire harness or connector
  3. Airbag sensor assembly
  4. DCM (Telematics Transceiver)

WIRING DIAGRAM


B278894E04


INSPECTION PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Check the DTC of "Airbag System" (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


2.INSPECT DCM (TELEMATICS TRANSCEIVER) (GSW SIGNAL)


    B240640E15
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I135-24 (GSW) - Body ground
    Engine switch on (IG)
    6.5 to 8.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (DCM (Telematics Transceiver))
    Reference Waveform 
    Item
    Condition
    Tester connection
    I135-24 (GSW) - Body ground
    Tool setting
    5.0 V/DIV., 20 ms/DIV.
    Vehicle condition
    Engine switch on (IG)

    Result:
    Result
    Proceed to
    8.5 V or higher
    A
    Below 6.5 V
    B
    6.5 to 8.5 V
    C



B
Go to step 4

C
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (FOR OPEN CIRCUIT)
  1. Remove the airbag sensor assembly but do not disconnect the connectors (Click here).



  1. w/ Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)



      B234641E06
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I47-24 (GSW3) - Body ground
      Engine switch on (IG)
      8.5 V or higher

      Text in Illustration 
      *a
      Component with harness connected
      (Airbag Sensor Assembly)
      Reference Waveform 
      Item
      Condition
      Tester connection
      I47-24 (GSW3) - Body ground
      Tool setting
      5.0 V/DIV., 20 ms/DIV.
      Vehicle condition
      Engine switch on (IG)



  1. w/ Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)



      B242282E13
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I47-24 (GSW3) - Body ground
      Engine switch on (IG)
      8.5 V or higher

      Text in Illustration 
      *a
      Component with harness connected
      (Airbag Sensor Assembly)
      Reference Waveform 
      Item
      Condition
      Tester connection
      I47-24 (GSW3) - Body ground
      Tool setting
      5.0 V/DIV., 20 ms/DIV.
      Vehicle condition
      Engine switch on (IG)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (FOR SHORT CIRCUIT)
  1. Disconnect the I135 DCM (Telematics Transceiver) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-24 (GSW) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 6
OK


5.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The engine switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

6.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the I135 DCM (Telematics Transceiver) connector.

  1. Disconnect the I47 airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-24 (GSW) - I47-24 (GSW3)
    Always
    Below 1 Ω
    I135-24 (GSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)