Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B1579    Voice Recognition Microphone Disconnected

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code
DTC Detection Condition
Trouble Area
B1579
Telephone microphone signal is lost.
  1. Roof console box assembly (telephone microphone assembly)
  2. DCM (telematics transceiver)*1
  3. Radio and display receiver assembly
  4. Harness or connector
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


E227676E08


INSPECTION PROCEDURE

NOTICE:
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E176671E95
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/ Manual (SOS) Switch
    A
    w/o Manual (SOS) Switch
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the DCM (telematics transceiver) connector.

  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-35 (MCI-) - S12-12 (MCO-)
    Always
    Below 1 Ω
    I135-35 (MCI-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER))
  1. Disconnect the radio and display receiver assembly connector.

  1. Disconnect the DCM (telematics transceiver) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-19 (MIN-) - I135-19 (MCO-)
    Always
    Below 1 Ω
    I155-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the radio and display receiver assembly connector.

  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I155-6 (SNS2) - S12-15 (SNS2)
    Always
    Below 1 Ω
    I155-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT DCM (TELEMATICS TRANSCEIVER)
  1. Reconnect the DCM (telematics transceiver) connector.

  1. Reconnect the radio and display receiver assembly connector.



    E176672E62
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-35 (MCI-) - Body ground
    Always
    Below 1 Ω

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    Text in Illustration 
    *a
    Component with harness connected
    (DCM (Telematics Transceiver))



B
Go to step 8
A

REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)  

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the radio and display receiver assembly connector.

  1. Disconnect the roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I155-6 (SNS2) - S12-15 (SNS2)
    Always
    Below 1 Ω
    I155-19 (MIN-) - S12-12 (MCO-)
    Always
    Below 1 Ω
    I155-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    E187117E23
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S12-15 (SNS2) - S12-12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)