Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Daytime Running Light Relay Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights (low-intensity high beam headlights) via the engine room junction block assembly.

WIRING DIAGRAM


E220270E02


INSPECTION PROCEDURE

1.CHECK OPERATION (HIGH BEAM HEADLIGHTS)
  1. Check the operation of the high beam headlights.

    OK:
    The high beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the daytime running lights illuminate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Daytime running lights
    ON/OFF
    -

    OK:
    The daytime running lights illuminate.



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here).

    OK:
    Output signal reading is normal.



NG
INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)


  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly (Click here).


    E230000E04

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A-1 (BATT) - Body ground
    Always
    11 to 14 V
    B-1 (ALT) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-3 (GND1) - Body ground
    Always
    Below 1 Ω
    1G-4 (GND2) - Body ground
    Always
    Below 1 Ω


Text in Illustration 
*a
Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
-
-


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3D main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-14 - 3D-23
    Always
    Below 1 Ω
    3D-23 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-23 - MB-25 (DRL)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Replace the engine room junction block assembly with a new or a known good one (Click here).

  1. Check that the daytime running lights operate normally.

    OK:
    The daytime running lights operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)