Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P0430  Catalyst System Efficiency Below Threshold (Bank 2)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stores the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Heated oxygen sensor (bank 1 sensor 2)

·

Exhaust manifold sub-assembly RH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)
P0430 Catalyst System Efficiency Below Threshold (Bank 2) The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Heated oxygen sensor (bank 2 sensor 2)

·

Exhaust manifold sub-assembly LH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)

CATALYST LOCATION

A255688C02
3.063,0.573 3.438,0.396 false 0.688,0.25 0.542,0.615 false 1.677,1.573 1.51,1.896 false 0.594,3.052 0.813,2.885 false 0.333,1.906 0.458,1.792 false 2.385,1.646 2.531,1.521 false 3.208,2.885 3.396,2.635 false 2.927,5.031 2.656,4.74 false 5.458,3.188 5.24,2.927 false 6.396,4.604 6.229,4.292 false 2.646,3.406 2.49,3.115 false 1.219,1.188 0.917,1.104 false 3.24,1.198 2.948,1.135 false 3.458,0.323 3.688,0.469 0.229,0.146 10 false *1 0.448,3 0.604,3.146 0.156,0.146 10 false *4 0.708,0.094 0.906,0.24 0.198,0.146 10 false *2 1.688,1.385 1.885,1.531 0.198,0.146 10 false *3 0.198,1.844 0.354,1.99 0.156,0.146 10 false *5 2.25,1.583 2.406,1.729 0.156,0.146 10 false *5 3.052,2.813 3.208,2.958 0.156,0.146 10 false *6 2.958,4.969 3.115,5.115 0.156,0.146 10 false *7 5.49,3.146 5.646,3.292 0.156,0.146 10 false *8 6.427,4.552 6.583,4.698 0.156,0.146 10 false *9 2.688,3.438 2.938,3.583 0.25,0.146 10 false *12 1.229,1.115 1.479,1.26 0.25,0.146 10 false *11 3.25,1.115 3.5,1.26 0.25,0.146 10 false *10
*1 Air Fuel Ratio Sensor (Bank 1 Sensor 1) *2 Air Fuel Ratio Sensor (Bank 2 Sensor 1)
*3 Heated Oxygen Sensor (Bank 1 Sensor 2) *4 Heated Oxygen Sensor (Bank 2 Sensor 2)
*5 TWC: Front Catalyst *6 TWC: Rear Catalyst
*7 Center Exhaust Pipe Assembly *8 Tail Exhaust Pipe Assembly RH
*9 Tail Exhaust Pipe Assembly LH *10 Exhaust Manifold Sub-assembly RH
*11 Exhaust Manifold Sub-assembly LH *12 Front Exhaust Pipe Assembly


NOTICE:
·

When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (*10) and the front exhaust pipe assembly (*12) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *1 and heated oxygen sensor *3).

·

When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (*11) and the front exhaust pipe assembly (*12) together when catalyst replacement is necessary (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4).



MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idling Off
Engine speed Less than 3200 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 70%
All of the following conditions are met 1, 2 and 3
1. Mass air flow 5 gm/sec or more, and less than 75 gm/sec
2. Front catalyst temperature (estimated) 570°C (1058°F) or higher, and less than 800°C (1472°F)
3. Rear catalyst temperature (estimated) 300°C (572°F) or higher, and less than 800°C (1472°F)
Shift position 3rd or higher

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A292988E06
1.323,0.854 1.75,0.333 false 1.75,0.333 2.083,0.333 false 0.333,0.25 1.323,0.448 0.99,0.198 10 Vehicle Speed 0.719,1.156 1.302,1.323 0.583,0.167 10 60 km/h 0.885,2.167 1.396,2.354 0.51,0.188 10 Idling 0.135,2.427 1.354,2.646 1.219,0.219 10 Ignition Switch off 1.771,2.698 2.688,2.938 0.917,0.24 10 Warming Up 2.979,2.708 4.354,2.938 1.375,0.229 10 10 minutes or more 5.531,2.708 6.792,2.938 1.26,0.229 10 10 minutes or more 0.302,3.469 4.917,3.667 4.615,0.198 10 *: Drive the vehicle while keeping the engine load as constant as possible. 2.135,0.25 3.792,0.448 1.656,0.198 10 Between 75 and 100 km/h 2.052,2.083 2.281,2.292 0.229,0.208 10 [A] 3.479,1.031 3.875,1.271 0.396,0.24 10 [B]* 4.385,3.156 4.677,3.406 0.292,0.25 10 [C] 6.042,0.646 6.396,0.906 0.354,0.26 10 [D]* 6.76,3.146 7,3.417 0.24,0.271 10 [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the tester on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the tester on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Enter the following menus: Powertrain / Engine / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0420 or P0430.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


15.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.



CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E74
4.906,3.073 4.906,3.292 false 4.906,3.292 5.26,3.292 false 5.198,3.073 5.198,3.292 false 3.625,0.896 3.885,1.125 0.26,0.229 10 (c) 0.573,0.646 1.583,0.865 1.01,0.219 10 Engine Speed 0.844,1.01 1.615,1.208 0.771,0.198 10 3000 rpm 0.844,1.583 1.594,1.781 0.75,0.198 10 2000 rpm 1.115,2.51 1.583,2.802 0.469,0.292 10 Idling 0.354,2.74 1.521,3 1.167,0.26 10 Ignition Switch off 1.656,2.646 1.917,2.885 0.26,0.24 10 (a) 2.073,2.438 2.354,2.688 0.281,0.25 10 (b) 4.792,0.896 5.063,1.146 0.271,0.25 10 (d) 5.094,1.458 5.406,1.74 0.313,0.281 10 (d) 2.094,3.104 3.01,3.302 0.917,0.198 10 Warming up 3.365,3.104 4.542,3.302 1.177,0.198 10 At least 3 minutes 5.302,3.219 6.115,3.417 0.813,0.198 10 2 seconds 4.865,3.323 5.333,3.542 0.469,0.219 10 Check 6.635,2.76 7.021,3.042 0.385,0.281 10 Time

(a) Connect the intelligent tester to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the tester.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the intelligent tester.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E18
2.804,0 7.147,0.163 4.343,0.163 10 Voltage Output When Active Air Fuel Ratio Control Not Performed: 6.016,0 7.147,0.163 1.132,0.163 10 Normal Catalyst 5.776,0 7.147,0.184 1.371,0.184 10 Deteriorated Catalyst 6.276,0 7.147,0.194 0.871,0.194 10 10 seconds 6.318,0 7.147,0.163 0.830,0.163 10 10 seconds 6.759,0 7.147,0.142 0.388,0.142 10 3.4 V 6.759,0 7.147,0.142 0.388,0.142 10 3.1 V 6.752,0 7.147,0.204 0.395,0.204 10 1.0 V 6.838,0 7.147,0.225 0.309,0.225 10 0 V 5.805,0 7.147,0.665 1.342,0.665 10 Waveform of Heated Oxygen Sensor Behind Three-Way Catalytic Converter 5.807,0 7.147,0.658 1.340,0.658 10 Waveform of Air Fuel Ratio Sensor in Front of Three-Way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 or P0174 (System Too Lean) and P0172 or P0175 (System Too Rich).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0420 and/or P0430 are output A
DTC P0420 and/or P0430 and other DTCs are output B


HINT:

If any DTCs other than P0420 and/or P0430 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the tester on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 234 2 35,37,44,48

f.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status AFS Voltage B1S1 or AFS Voltage B2S1 Status O2S B1S2 or O2S B2S2 Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

4.REPLACE AIR FUEL RATIO SENSOR

C

5.CHECK FOR EXHAUST GAS LEAK

D

7.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

6.REPLACE HEATED OXYGEN SENSOR

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
6.REPLACE HEATED OXYGEN SENSOR
a.

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0171


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0420 and/or P0430 is output A
DTC is not output B



A

11.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

B

END

11.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
NOTICE:
·

When outputting DTC P0420 replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

·

When outputting DTC P0430 replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.



HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0420 is output A
DTC P0430 is output B
DTC P0420 and P0430 are output C



A

REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS

FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS


B

REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS

FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS


C

REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH AND LH (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

EXHAUST MANIFOLD SUB-ASSEMBLY RH AND LH (TWC: FRONT CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS

FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST): Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS