This Electronic Throttle Control System (ETCS) does not use a throttle cable.
These DTCs relate to the accelerator pedal position sensor.
The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2120 | Throttle / Pedal Position Sensor / Switch "D" Circuit | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
| P2122 | Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCPA circuit ·
Open or ground short in VPA circuit ·
ECM |
Comes on | DTC stored |
| P2123 | Throttle / Pedal Position Sensor / Switch "D" Circuit High Input | VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in EPA circuit ·
ECM |
Comes on | DTC stored |
| P2125 | Throttle / Pedal Position Sensor / Switch "E" Circuit | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
| P2127 | Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCP2 circuit ·
Open or ground short in VPA2 circuit ·
ECM |
Comes on | DTC stored |
| P2128 | Throttle / Pedal Position Sensor / Switch "E" Circuit High Input | Both of the following conditions continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
·
Accelerator pedal sensor assembly ·
Open in EPA2 circuit ·
ECM |
Comes on | DTC stored |
| P2138 | Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation | Either of the following conditions continues for 2.0 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less. (b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less. |
·
Short between VPA and VPA2 circuits ·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
When any of these DTCs are output, check the accelerator pedal position sensor voltage using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
| Trouble Area | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed | ||
|---|---|---|---|---|
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.98 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.98 V |
Accelerator pedal positions are expressed as voltages.
When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is more than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.
Example:
When the output voltage of VPA is less than 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.
| Required Sensors/Components | Accelerator pedal sensor assembly |
| Frequency of Operation | Continuous |
| VPA voltage | Higher than 0.4 V, and less than 4.8 V |
| VPA2 voltage | Higher than 1.2 V, and less than 4.8 V |
| Difference between VPA and VPA2 voltages | Higher than 0.02 V |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on [A].
Fully depress and release the accelerator pedal [B].
Check that 5 seconds or more have elapsed since the ignition switch is turned ON.
Enter the following menus: Powertrain / Engine / DTC [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.
When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Fully Depressed |
| *b | Fully Released |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
| Tester Display |
|---|
| Accel Sensor Out No.1 |
| Accel Sensor Out No.2 |
Read the value displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No.1 | Accel Sensor Out No.2 |
|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.98 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-6 (VPA) - A25-54 (VPA) | Always | Below 1 Ω |
| A36-5 (EPA) - A25-55 (EPA) | Always | Below 1 Ω |
| A36-4 (VCPA) - A25-56 (VCPA) | Always | Below 1 Ω |
| A36-3 (VPA2) - A25-57 (VPA2) | Always | Below 1 Ω |
| A36-2 (EPA2) - A25-58 (EPA2) | Always | Below 1 Ω |
| A36-1 (VCP2) - A25-59 (VCP2) | Always | Below 1 Ω |
| A36-6 (VPA) or A25-54 (VPA) - Body ground | Always | 10 kΩ or higher |
| A36-4 (VCPA) or A25-56 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A36-3 (VPA2) or A25-57 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A36-1 (VCP2) or A25-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-4 (VCPA) - A36-5 (EPA) | ignition switch ON | 4.5 to 5.5 V |
| A36-1 (VCP2) - A36-2 (EPA2) | ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTC is not output | B |
A
B