Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0115 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0115).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance Problem Either of the following conditions is met (2 trip detection logic):
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and then next cold engine start is performed, the engine coolant temperature sensor value does not change.


·

Thermostat

·

Engine coolant temperature sensor


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Cold Start Monitor

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


Engine Coolant Temperature Sensor Soak Monitor

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


MONITOR STRATEGY

Required Sensors/Components Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A198823E58
0.906,1.104 1.469,1.292 0.563,0.188 10 false 40 km/h 1.063,1.698 1.448,1.927 0.385,0.229 10 false Idling 2.75,2.573 3.99,2.844 1.24,0.271 10 false 5 minutes or more 4.167,0.167 5.917,0.438 1.75,0.271 10 false Total of 5 minutes or more 2.104,1.938 2.333,2.156 0.229,0.219 10 false [A] 3.24,1.656 3.479,1.896 0.24,0.24 10 false [B] 3.979,2.885 4.24,3.135 0.26,0.25 10 false [C] 6.146,2.885 6.385,3.135 0.24,0.25 10 false [E] 0.5,2 1.438,2.313 0.938,0.313 10 false Ignition Switch ON 4.865,0.667 5.135,0.927 0.271,0.26 10 false [D] 1.385,3.198 6.365,3.542 4.979,0.344 10 false HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the tester on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / Engine / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0116.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


15.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.



CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are output simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs and other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

Inspect the thermostat (thermostat opening temperature).

Click hereEngine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG