Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074415 REAR CRANKSHAFT OIL SEAL A

2GR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11381A 1.INSTALL ENGINE REAR OIL SEAL

a.
A132245
2.711,1.319 3.021,1.475 0.309,0.156 10 SST 2.626,2.863 2.935,3.019 0.309,0.156 10 SST 0.995,2.607 1.16,2.764 0.165,0.156 10 *1 1.949,2.376 2.12,2.532 0.17,0.156 10 *a 2.115,1.153 2.686,1.416 false 2.13,3.201 2.591,2.96 false 1.508,2.694 1.186,2.694 false
*1 Retainer
*a Oil seal tap in depth
(-0.5 to 0.5 mm)


Apply MP grease to a new engine rear oil seal lip.


b.

Using SST and a hammer, tap in the engine rear oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Oil seal tap in depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using SST, hold the crankshaft pulley.

SST
09213-70011  (09213-70020)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A114342

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A192405
1.021,0.208 1.365,0.208 false 2.521,3.385 2.854,3.219 false 0.823,0.115 0.979,0.26 0.156,0.146 10 false *1 2.896,3.135 3.063,3.281 0.167,0.146 10 false *2
*1 Drive Plate
*2 Rear Spacer
V100135

Transaxle Side


Install the drive plate and ring gear sub-assembly and rear drive plate spacer onto the crankshaft.


e.
P000601
1.979,1.188 2.313,0.323 false 2.333,0.229 2.531,0.417 0.198,0.188 10 false *1
*1 Adhesive


Apply adhesive to 2 or 3 threads of each bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A306206
1.885,0.281 2.042,0.479 0.156,0.198 10 false 1 1.875,1.573 2.031,1.771 0.156,0.198 10 false 2 1.167,0.979 1.323,1.177 0.156,0.198 10 false 3 2.427,0.865 2.583,1.063 0.156,0.198 10 false 4 1.354,0.448 1.51,0.646 0.156,0.198 10 false 5 2.323,1.396 2.479,1.594 0.156,0.198 10 false 6 2.354,0.531 2.51,0.729 0.156,0.198 10 false 7 1.375,1.438 1.531,1.635 0.156,0.198 10 false 8

In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.