Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074471 AUTOMATIC TRANSAXLE ASSEMBLY A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C154963

Engage the splines of the input shaft and turbine runner.


b.
C154964

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm (0.393 in.) and engage the splines while rotating the torque converter assembly.



c.
C154965

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter assembly set bolt holes.


e.
C191042
1,2.354 1,2.948 false 1.396,0.948 1.24,0.292 1.24,0.292 1.115,0.292 false 2.552,0.802 2.417,0.927 2.417,0.927 2.417,1.042 false 2.688,1.5 2.563,1.635 2.563,1.635 2.563,1.74 false 2.156,0.323 2.271,0.469 0.115,0.146 10 false A 0.927,0.198 1.385,0.49 0.458,0.292 10 false *a 0.906,2.958 1.083,3.135 0.177,0.177 10 false *b 2.479,1.781 3.042,2.156 0.563,0.375 10 false *b 2.354,1.083 2.792,1.365 0.438,0.281 10 false *a
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the automatic transaxle assembly contact surface of the engine*a and the torque converter assembly contact surface of the drive plate*b.


f.
C191041
2.378,0.341 2.499,0.498 0.121,0.156 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 33403M 2.INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

a.

Apply ATF to a new O-ring and install it to the speedometer driven hole (ATM) cover sub-assembly.


b.

Install the speedometer driven hole (ATM) cover sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 5 wire harness clamp brackets to the automatic transaxle assembly with the 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12311A 5.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket with the 3 bolts.

Torque:
64 N*m (652 kgf*cm, 47 ft.*lbf)


Hide 30500 6.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C206210
0.869,0.952 1.022,1.119 0.153,0.168 10 *1 2.198,0.98 2.351,1.148 0.153,0.168 10 *2 1.498,1.06 2.161,1.06 false
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece


Apply clutch spline grease round of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C243147
1.227,2.361 1.38,2.514 0.153,0.153 10 A 1.643,2.311 1.796,2.464 0.153,0.153 10 A 0.902,2.744 1.055,2.897 0.153,0.153 10 B 2.553,2.381 2.706,2.534 0.153,0.153 10 A 2.731,2.979 2.884,3.132 0.153,0.153 10 A 2.791,3.576 2.944,3.729 0.153,0.153 10 A 2.731,3.895 2.884,4.048 0.153,0.153 10 A 2.43,4.225 2.582,4.378 0.153,0.153 10 C 1.396,4.364 1.549,4.517 0.153,0.153 10 C 1.108,4.169 1.261,4.322 0.153,0.153 10 C

While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 10 bolts shown in the illustration.

Torque:
Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt B : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt C : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the automatic transaxle assembly contact surface of the engine cylinder block before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.



HINT:

Bolt length:

·

Bolt A: 55 mm (2.17 in.)

·

Bolt B: 50 mm (1.97 in.)

·

Bolt C: 33 mm (1.30 in.)




c.

Clean and degrease the bolt and the installation hole in the automatic transaxle assembly.


d.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.
C243148
0.792,1.763 0.94,1.936 0.148,0.173 10 D

Install the bolt.

Torque:
Bolt D : 46 N*m (469 kgf*cm, 34 ft.*lbf)

HINT:

Bolt length:

Bolt D: 41 mm (1.61 in.)




Hide 35123A 7.INSTALL TRANSMISSION BREATHER SKIRT

a.

Install the clamp to the transmission breather skirt.


b.

Install the transmission breather skirt with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the breather plug.


Hide 8.INSTALL WIRE HARNESS

a.

Connect the 7 clamps and connector.


b.

Install the wire harnesses with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 51100G 10.INSTALL FRONT FRAME ASSEMBLY

Hide 11.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 12.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION