Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR
RM2030EQ _51 Engine / Hybrid System _014636 2GR-FE FUEL _0074421 FUEL INJECTOR G

2GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.
A182852

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.



b.

Inspect the injector injection.

CAUTION:

Keep the injector away from sparks during the test.


i.
A264971
0.531,1.656 0.76,1.885 0.76,1.885 0.865,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.281 2.292,1.583 2.292,1.583 2.417,1.583 false 2.615,0.719 2.917,0.417 2.917,0.417 3.031,0.417 false 0.885,1.792 1.063,1.969 0.177,0.177 10 false *1 1.302,0.542 1.531,0.781 0.229,0.24 10 false *2 2.448,1.51 2.625,1.688 0.177,0.177 10 false *3 3.094,0.344 3.271,0.521 0.177,0.177 10 false *4
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Fuel Tube Connector)
*4 Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.

Install a new O-ring onto the fuel injector assembly.


iii.
A264982
1.333,0.135 0.958,0.135 false 1.74,0.333 2.031,0.333 false 1.302,0.771 0.958,0.771 false 1.5,1.167 1.667,1.167 false 2.115,1.448 2.458,1.448 false 1.313,1.875 0.969,1.875 false 0.792,0.052 0.979,0.219 0.188,0.167 10 false *1 2.063,0.281 2.229,0.458 0.167,0.177 10 false *2 0.792,0.698 0.958,0.875 0.167,0.177 10 false *3 1.698,1.094 1.865,1.271 0.167,0.177 10 false *4 2.5,1.354 2.667,1.531 0.167,0.177 10 false *5 0.792,1.813 0.958,1.99 0.167,0.177 10 false *6
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Adapter)
*4 O-ring
*5 SST
(Clamp)
*6 Vinyl Tube


Connect SST (adapter and hose) to the injector assembly, and hold the injector assembly and union with SST (clamp).

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)


iv.

Install a vinyl tube onto the injector.

CAUTION:

Install a suitable vinyl tube onto the injector assembly to prevent gasoline from spraying.



v.
A261671
2.01,1.719 2.219,1.927 2.219,1.927 2.302,1.927 false 1.917,0.396 2.323,0.396 false 1.219,0.615 0.833,0.615 false 2.365,0.323 2.542,0.51 0.177,0.188 10 false *1 0.646,0.552 0.906,0.781 0.26,0.229 10 false *2 2.354,1.865 2.531,2.052 0.177,0.188 10 false *3
*1 SST
(Adapter)
*2 SST
(Tie Band)
*3 SST
(Clamp)


Tie the clamp and adapter together with a tie band as shown in the illustration.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41800)


vi.

Put the injector into the graduated cylinder.



viii.
A264973
2.021,0.552 2.021,0.969 false 1.958,1.01 2.115,1.25 0.156,0.24 10 *1 1.021,1.333 1.177,1.573 0.156,0.24 10 *a
*1 SST
(Wire)
*a Connect


Connect SST (wire) to the injector assembly and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive (+) terminal - Ground terminal Per 15 seconds 76 to 91 cc (4.6 to 5.6 cu.in.)


Difference between each injector:

15 cc (0.9 cu.in.) or less


NOTICE:

Always switch the voltage on and off at the battery side, not the injector side.


If the injection volume is not as specified, replace the injector assembly.



c.

Check for fuel drop.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel drop from the injector.

Standard fuel drop:

1 drop or less every 35 minutes


If fuel drop is not as specified, replace the fuel injector assembly.