Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR
RM2030EQ _51 Engine / Hybrid System _014636 2GR-FE FUEL _0074421 FUEL INJECTOR A

2GR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17190 4.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 23901 5.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A305779C01
2.802,4.063 2.802,3.688 false 2.698,3.25 2.479,2.969 2.479,2.969 2.375,2.969 false 1.365,3.375 1.146,3.094 1.146,3.094 1.042,3.094 false 2,3.719 2.104,4.052 2.104,4.052 2.177,3.719 false 2.375,2.198 2.375,1.656 true 2.313,2.26 2.625,2.417 0.313,0.156 10 false *1 2.198,2.896 2.51,3.052 0.313,0.156 10 false *2 0.865,3.021 1.177,3.177 0.313,0.156 10 false *3 2.01,4.094 2.323,4.25 0.313,0.156 10 false *4 2.729,4.104 3.042,4.26 0.313,0.156 10 false *5
*1 No. 2 Fuel Pipe Clamp
*2 Fuel Tube Connector
*3 Nylon Tube
*4 O-ring
*5 Fuel Pipe
V100135

Pinch
V100136

Pull


Remove the No. 2 fuel pipe clamp.


b.

Pinch the tube connector and pull out the fuel pipe.

NOTICE:
·

Check that there is no dirt or other foreign objects around the fuel tube connector when disconnecting it. Clean the fuel tube connector as necessary.

·

It is necessary to prevent dirt or foreign objects from entering the fuel tube connector. If dirt or foreign objects get in the fuel tube connector, the O-rings may not seal properly.

·

Only disconnect the fuel tube connector by hand.

·

Do not bend, kink or twist the nylon tubes.

·

Protect the fuel tube connector by covering it with a plastic bag.

·

If the fuel pipe and the fuel tube connector are stuck, carefully try wiggling or pushing and pulling on the fuel tube connector to release it. Pull the fuel tube connector off carefully.




Hide 23807 6.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A137341

Disconnect the 6 fuel injector connectors.


b.
A129471

Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



c.
A292481

Remove the 6 injector vibration insulators from the intake manifold.


Hide 23250 7.REMOVE FUEL INJECTOR ASSEMBLY

a.
A129473

Pull the 6 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

NOTICE:

If the injectors are to be reused, reinstall them to the same cylinder they came from.



b.
A129475C01
2.875,1.438 2.875,1.583 false 2.833,1.625 3.25,1.979 0.417,0.354 10 *1
*1 O-ring


Remove the O-ring from each fuel injector assembly.


c.

For reinstallation, attach a tag or label to each injector shaft.

NOTICE:

Prevent entry of foreign matter by covering the fuel injectors with plastic bags.