77020A
1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
2.DRAIN FUEL
17420
3.REMOVE CENTER EXHAUST PIPE ASSEMBLY
57536A
4.REMOVE FRONT FLOOR BRACE LH (for Sport Package)
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and front floor brace LH.
57535A
5.REMOVE FRONT FLOOR BRACE RH (for Sport Package)
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and front floor brace RH.
46420
6.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt and nut, and separate the No. 2 parking brake cable assembly.
46430
7.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt and nut, and separate the No. 3 parking brake cable assembly.
48832A
8.REMOVE REAR NO. 1 STABILIZER BAR BRACKET
Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets.
77631A
9.REMOVE LOWER CENTER FUEL TANK PROTECTOR
Remove the 4 bolts and lower center fuel tank protector.
77209B
10.DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY
| *a | Retainer |
| *b | Fuel Pipe |
| *c | Fuel Tube Connector |
| *d | O-ring |
|
Pinch |
|
Pull |
Disconnect the fuel pump tube sub-assembly.
Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.
Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
Be sure to disconnect the fuel tube connector by hand.
If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.
Be sure to disconnect the fuel tube connector by hand.
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
77100
11.REMOVE FUEL TANK ASSEMBLY
Slide the clip and disconnect the fuel emission hose from the charcoal canister assembly.
Support the fuel tank assembly using an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 2 bolts of the fuel tank bands.
Slightly lower the engine lifter.
Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
Loosen the clamp, then disconnect the breather tube fuel hose from the fuel tank assembly.
Lower the engine lifter to remove the fuel tank assembly.
Slowly operate the engine lifter to lower the fuel tank assembly.
Be careful not to drop the fuel tank assembly.
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.
| *1 | Pin |
| *2 | Fuel Tank Band |
Remove the 2 pins and 2 fuel tank bands as shown in the illustration.
Remove the 4 clip nuts from the fuel tank assembly.
77651A
12.REMOVE NO. 1 FUEL TANK CUSHION
Remove the No. 1 fuel tank cushion from the fuel tank assembly.
77652A
13.REMOVE NO. 2 FUEL TANK CUSHION
Remove the 7 No. 2 fuel tank cushions from the fuel tank assembly.
77642A
14.REMOVE NO. 2 FUEL TANK PROTECTOR
Disengage the 2 claws, and remove the No. 2 fuel tank protector by sliding it as shown in the illustration.
77643A
15.REMOVE NO. 3 FUEL TANK PROTECTOR
Disengage the 2 claws, and remove the No. 3 fuel tank protector by sliding it as shown in the illustration.
77340A
16.REMOVE FUEL CUT OFF WITH TUBE VALVE ASSEMBLY
| *1 | Fuel Tank Breather Tube Gasket |
| *2 | Fuel Cut Off with Tube Valve Assembly |
| *3 | Fuel Emission Hose |
| *a | Fuel Cut Off Valve |
Slide the clip and disconnect the fuel emission hose from the fuel cut off with tube valve assembly.
Disengage the 2 clamps to disconnect the fuel cut off with tube valve assembly from the fuel tank assembly.
Insert a clip remover between the fuel cut off valve and fuel tank breather tube gasket and remove the fuel cut off valve by gradually pushing it upward.
Work carefully to maintain the sealing integrity of the fuel cut off valve as it is made from resin and easy to be damaged if forcibly removing and installing it.
Be sure to install a new fuel cut off with tube valve assembly and 2 new fuel tank breather tube gaskets.
Remove the 2 fuel tank breather tube gaskets from the fuel tank assembly.
77209B
17.REMOVE FUEL PUMP TUBE SUB-ASSEMBLY
Disengage the 2 clamps to remove the fuel pump tube sub-assembly from the fuel tank assembly.
77246C
18.REMOVE FUEL MAIN TUBE SUPPORT
Remove the bolt and fuel main tube support from the fuel tank assembly.
77289C
19.REMOVE NO. 4 FUEL TUBE CLAMP
Remove the 3 No. 4 fuel tube clamps from the fuel tank assembly.
77011
20.REMOVE LOWER FUEL TANK FILLER PIPE SUB-ASSEMBLY
Remove the 5 bolts, lower fuel tank filler pipe sub-assembly and gasket from the fuel tank assembly.