The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.
| *a | ON-OFF |
| *b | -/SET |
| *c | +/RES |
| *d | CANCEL |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select the following menu items: Powertrain / Cruise Control / Data List.
Check the Data List to confirm proper functioning of the cruise control switch.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main SW M-CPU | Cruise control switch signal (Main CPU) | ON or OFF | ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released |
- |
| Cancel Switch | CANCEL switch signal | ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| SET/COAST Switch | -/SET switch signal | ON or OFF | ON: -/SET switch on
OFF: -/SET switch off |
- |
| RES/ACC Switch | +/RES switch signal | ON or OFF | ON: +/RES switch on
OFF: +/RES switch off |
- |
| Tester Display |
|---|
| Main SW M-CPU |
| Cancel Switch |
| SET/COAST Switch |
| RES/ACC Switch |
When the cruise control switch is operated, the display changes as shown above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the cruise control switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *1 | Cruise Control Switch (ON-OFF button) | - | - |
| *a | Component without harness connected
(Cruise Control Switch) |
*b | ON-OFF |
| *c | +/RES | *d | -/SET |
| *e | CANCEL | - | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 3 | Cruise control switch (ON-OFF button) released | 1 MΩ or higher |
| Cruise control switch (ON-OFF button) pushed | Below 2.5 Ω | |
| +/RES | 235 to 245 Ω | |
| -/SET | 617 to 643 Ω | |
| CANCEL | 1509 to 1571 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
| *b | Front view of wire harness connector
(to Cruise Control Switch) |
Disconnect the spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| Cruise control switch side connector terminal 3 - z2-3 | Below 1 Ω |
| Cruise control switch side connector terminal 1 - z2-4 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.
Removal
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Installation
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
Remove the spiral cable sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-3 - I28-1 (CCS) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-4 - I28-2 (ECC) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-3 - I28-1 (CCS) | Always | Below 3 Ω |
| z2-4 - I28-2 (ECC) | Always | Below 3 Ω |
The spiral cable sub-assembly makes a maximum of approximately 5 rotations.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-47 (CCS) - I28-1 (CCS) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-47 (CCS) or I28-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-2 (ECC) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG