Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM2030EQ _51 Engine / Hybrid System _014642 CRUISE CONTROL _0074459 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more
·

Stop light switch assembly

·

Stop light switch circuit

·

ECM



WIRING DIAGRAM

E236799E05
6.248,4.199 6.598,4.348 0.350,0.149 10 ECM 5.856,4.199 6.207,4.348 0.350,0.149 10 A25 5.57,0.653 5.742,0.808 0.172,0.156 10 51 5.57,1.363 5.742,1.519 0.172,0.156 10 36 3.036,1.749 3.314,1.898 0.277,0.149 10 A33 3.022,1.906 4.796,2.066 1.774,0.159 10 Stop Light Switch Assembly 4.317,0.638 4.421,0.797 0.104,0.159 10 1 3.293,0.638 3.397,0.797 0.104,0.159 10 2 4.313,1.348 4.468,1.507 0.155,0.159 10 3 3.287,1.354 3.449,1.513 0.162,0.159 10 4 2.168,0.91 2.570,1.062 0.402,0.152 10 STOP 1.861,1.611 2.821,1.763 0.960,0.152 10 ECU-IG2 No. 3 0.953,4.336 1.495,4.488 0.541,0.152 10 ST/AM2 3.81,4.336 4.896,4.488 1.086,0.152 10 ECU-IG2 No. 1 3.109,5.341 3.704,5.494 0.595,0.152 10 FL MAIN 1.053,0.91 1.336,1.062 0.283,0.152 10 ALT 4.557,5.949 5.026,6.101 0.468,0.152 10 Battery 1.887,4.072 1.991,4.232 0.104,0.159 10 5 3.044,4.072 3.148,4.232 0.104,0.159 10 6 2.068,4.277 2.376,4.424 0.309,0.147 10 AM2 2.71,4.282 2.958,4.429 0.248,0.147 10 IG2 5.862,0.727 6.155,0.880 0.294,0.154 10 STP 5.862,1.452 6.188,1.606 0.327,0.154 10 ST1- 2.023,4.677 2.940,4.837 0.917,0.161 10 Ignition Switch 0.126,0.118 2.734,0.292 2.608,0.174 12 w/o Smart Entry and Start System: 2.016,4.53 2.307,4.679 0.291,0.149 10 I36 1.36,3.014 2.005,3.161 0.646,0.147 10 IG2-MAIN 4.191,3.569 4.440,3.716 0.248,0.147 10 IG2

E236800E09
6.5,4.771 6.854,4.917 0.354,0.146 10 false ECM 6.115,4.771 6.469,4.917 0.354,0.146 10 false A25 5.885,0.896 6.146,1.104 0.26,0.208 10 false 51 5.885,1.677 6.063,1.833 0.177,0.156 10 false 36 3.208,2.135 3.49,2.281 0.281,0.146 10 false A33 3.208,2.313 4.969,2.469 1.76,0.156 10 false Stop Light Switch Assembly 4.635,0.875 4.74,1.031 0.104,0.156 10 false 1 3.458,0.875 3.563,1.031 0.104,0.156 10 false 2 4.635,1.656 4.792,1.813 0.156,0.156 10 false 3 3.448,1.656 3.615,1.813 0.167,0.156 10 false 4 2.427,1.135 2.833,1.292 0.406,0.156 10 false STOP 2.156,1.906 3.125,2.063 0.969,0.156 10 false ECU-IG2 No. 3 3.542,3.26 3.927,3.417 0.385,0.156 10 false IG2D 3.333,3.156 3.469,3.313 0.135,0.156 10 false 9 4.552,3.219 4.844,3.375 0.292,0.156 10 false A43 4.552,3.375 5.677,3.531 1.125,0.156 10 false Certification ECU 1.573,4.417 1.854,4.573 0.281,0.156 10 false ALT 4.667,4.854 5.135,5.01 0.469,0.156 10 false Battery 1.354,2.563 1.604,2.708 0.25,0.146 10 false IG2 6.146,0.958 6.438,1.115 0.292,0.156 10 false STP 6.146,1.76 6.469,1.917 0.323,0.156 10 false ST1- 0.177,0.135 3.552,0.438 3.375,0.302 12 false w/ Smart Entry and Start System: 1.396,3.896 2.073,4.042 0.677,0.146 10 false IG2-MAIN 3.188,4.417 3.781,4.563 0.594,0.146 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
a.
E144327C07
0.458,2.073 0.792,2.375 0.333,0.302 0.51,2.146 0.969,2.344 0.458,0.198 10 false A33 0.167,0.208 0.625,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
E144327C07
0.458,2.073 0.792,2.375 0.333,0.302 0.51,2.146 0.969,2.344 0.458,0.198 10 false A33 0.167,0.208 0.625,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A33-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
E145496C11
0.167,0.135 0.417,0.427 0.25,0.292 10 false *a 0.667,2.552 0.917,2.844 0.25,0.292 10 false *b 1.26,2.563 1.51,2.854 0.25,0.292 10 false *c
*a Component without harness connected
(Stop Light Switch Assembly)
*b Not pushed
*c Pushed


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 0.1 Ω
3 - 4 Switch pin not pushed 10 kΩ or higher
1 - 2 Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin pushed Below 200 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A25-51 (STP) - A33-1 Always Below 1 Ω
A25-36 (ST1-) - A33-3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A25-51 (STP) or A33-1 - Body ground Always 10 kΩ or higher
A25-36 (ST1-) or A33-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)